Omron NX Series - Page 105

A - 39
Appendices
NX-series Data Reference Manual (W525)
A-6 Version Information with Commnica-
tions Coupler Units
A
A-6-2 Connection to an EtherNet/IP Coupler Unit
 Temperature Input Units
 Heater Burnout Detection Units
NX Units Corresponding unit versions/versions
Model
Unit
version
Application with an NJ/NX/NY-series Con-
troller
*1
*1. Refer to the user’s manual for the EtherNet/IP Coupler Units for information on the unit versions of EtherNet/IP Units that
are compatible with EtherNet/IP Coupler Units.
Application with a CS/CJ/CP-series PLC
*2
*2. Refer to the user’s manual for the EtherNet/IP Coupler Units for information on the unit versions of CPU Units and
EtherNet/IP Units that are compatible with EtherNet/IP Coupler Units.
EtherNet/IP
Coupler
Unit
CPU Unit or
Industrial
PC
Sysmac Stu-
dio
EtherNet/IP
Coupler
Unit
Sysmac Stu-
dio
NX-IO Con-
figurator
*3
*3. For connection to an EtherNet/IP Coupler Unit with unit version 1.0, You can connect only to the peripheral USB port on
the EtherNet/IP Coupler Unit. You cannot connect with any other path. If you need to connect by another path, use an
EtherNet/IP Coupler Unit with unit version 1.2 or later.
NX-TS2101 Ver. 1.0 Ver. 1.2 Ver. 1.14 Ver. 1.19 Ver. 1.0 Ver. 1.10 Ver. 1.00
Ver. 1.1
NX-TS2102 Ver. 1.1
NX-TS2104 Ver. 1.1
NX-TS2201 Ver. 1.0
Ver. 1.1
NX-TS2202 Ver. 1.1
NX-TS2204 Ver. 1.1
NX-TS3101 Ver. 1.0
Ver. 1.1
NX-TS3102 Ver. 1.1
NX-TS3104 Ver. 1.1
NX-TS3201 Ver. 1.0
Ver. 1.1
NX-TS3202 Ver. 1.1
NX-TS3204 Ver. 1.1
NX Units Corresponding unit versions/versions
Model
Unit
version
Application with an NJ/NX/NY-series
Controller
*1
*1. Refer to the user’s manual for the EtherNet/IP Coupler Units for information on the unit versions of EtherNet/IP Units that
are compatible with EtherNet/IP Coupler Units.
Application with a CS/CJ/CP-series PLC
*2
*2. Refer to the user’s manual for the EtherNet/IP Coupler Units for information on the unit versions of CPU Units and
EtherNet/IP Units that are compatible with EtherNet/IP Coupler Units.
EtherNet/IP
Coupler
Unit
CPU Unit or
Industrial
PC
Sysmac
Studio
EtherNet/IP
Coupler
Unit
Sysmac
Studio
NX-IO Con-
figurator
*3
*3. For connection to an EtherNet/IP Coupler Unit with unit version 1.0, You can connect only to the peripheral USB port on
the EtherNet/IP Coupler Unit. You cannot connect with any other path. If you need to connect by another path, use an
EtherNet/IP Coupler Unit with unit version 1.2 or later.
NX-HB3101 Ver. 1.0 Ver. 1.2 Ver. 1.14 Ver. 1.19 Ver. 1.0 Ver. 1.16 Ver. 1.00
NX-HB3201