Omron NX Series - Page 107

A - 41
Appendices
NX-series Data Reference Manual (W525)
A-6 Version Information with Commnica-
tions Coupler Units
A
A-6-2 Connection to an EtherNet/IP Coupler Unit
 Communications Interface Units
 Load Cell Input Unit
 IO-Link Master Unit
NX Units Corresponding unit versions/versions
Model
Unit
version
Application with an NJ/NX/NY-series
Controller
*1
*1. Refer to the user’s manual for the EtherNet/IP Coupler Units for information on the unit versions of EtherNet/IP Units that
are compatible with EtherNet/IP Coupler Units.
Application with a CS/CJ/CP-series PLC
*2
*2. Refer to the user’s manual for the EtherNet/IP Coupler Units for information on the unit versions of CPU Units and
EtherNet/IP Units that are compatible with EtherNet/IP Coupler Units.
EtherNet/IP
Coupler
Unit
CPU Unit or
Industrial
PC
Sysmac
Studio
EtherNet/IP
Coupler
Unit
Sysmac
Studio
NX-IO Con-
figurator
*3
*3. For connection to an EtherNet/IP Coupler Unit with unit version 1.0, You can connect only to the peripheral USB port on
the EtherNet/IP Coupler Unit. You cannot connect with any other path. If you need to connect by another path, use an
EtherNet/IP Coupler Unit with unit version 1.2 or later.
NX-CIF101 Ver. 1.0 Ver. 1.2 Ver. 1.14 Ver. 1.19 Ver. 1.2 Ver. 1.19 Ver. 1.00
NX-CIF105
NX-CIF210
NX Units Corresponding unit versions/versions
Model
Unit
version
Application with an NJ/NX/NY-series
Controller
*1
*1. Refer to the user’s manual for the EtherNet/IP Coupler Units for information on the unit versions of EtherNet/IP Units that
are compatible with EtherNet/IP Coupler Units.
Application with a CS/CJ/CP-series PLC
*2
*2. Refer to the user’s manual for the EtherNet/IP Coupler Units for information on the unit versions of CPU Units and
EtherNet/IP Units that are compatible with EtherNet/IP Coupler Units.
EtherNet/IP
Coupler
Unit
CPU Unit or
Industrial
PC
Sysmac
Studio
EtherNet/IP
Coupler
Unit
Sysmac
Studio
NX-IO Con-
figurator
*3
*3. For connection to an EtherNet/IP Coupler Unit with unit version 1.0, You can connect only to the peripheral USB port on
the EtherNet/IP Coupler Unit. You cannot connect with any other path. If you need to connect by another path, use an
EtherNet/IP Coupler Unit with unit version 1.2 or later.
NX-RS1201 Ver. 1.0 Ver. 1.2 Ver. 1.14 Ver. 1.19 Ver. 1.0 Ver. 1.16 Ver. 1.00
NX Units Corresponding unit versions/versions
Model
Unit
version
Application with an NJ/NX/NY-series
Controller
*1
*1. Refer to the user’s manual for the EtherNet/IP Coupler Units for information on the unit versions of EtherNet/IP Units that
are compatible with EtherNet/IP Coupler Units.
Application with a CS/CJ/CP-series PLC
*2
*2. Refer to the user’s manual for the EtherNet/IP Coupler Units for information on the unit versions of CPU Units and
EtherNet/IP Units that are compatible with EtherNet/IP Coupler Units.
EtherNet/IP
Coupler
Unit
CPU Unit or
Industrial
PC
Sysmac
Studio
EtherNet/IP
Coupler
Unit
Sysmac
Studio
NX-IO Con-
figurator
*3
*3. For connection to an EtherNet/IP Coupler Unit with unit version 1.0, You can connect only to the peripheral USB port on
the EtherNet/IP Coupler Unit. You cannot connect with any other path. If you need to connect by another path, use an
EtherNet/IP Coupler Unit with unit version 1.2 or later.
NX-ILM400 Ver. 1.0 Ver. 1.2 Ver. 1.14 Ver. 1.19 Ver. 1.0 Ver. 1.16 Ver. 1.00
Ver. 1.1 Ver. 1.20 Ver. 1.01