Panasonic AG-CX350

– 86 –
Chapter 4 Operation — Menu settings
[SDI OUT HDR]
Sets the output image from the <SDI OUT> terminal.
[SDR] Outputs in the standard dynamic range.
[HDR] Outputs in the high dynamic range.
(Factory setting: [HDR])
@@
NOTE
t The setting is xed to [SDR] when set to following menu.
‑ [SYSTEM] menu → [REC FORMAT] → [480-59.94i/AVCHD SA]
‑ [SYSTEM] menu → [REC FORMAT] → [576-50.00i/AVCHD SA]
‑ [VIDEO OUT/LCD/VF] menu → [SDI OUT] → [OUT FORMAT] → [720×480i]
‑ [VIDEO OUT/LCD/VF] menu → [SDI OUT] → [OUT FORMAT] → [720×576i]
t When the [SCENE FILE] menu → [GAMMA MODE SEL] is set to anything other than [HLG], the camera image is output in the standard dynamic
range.
t This cannot be set when the [SYSTEM] menu → [COLOR SETTING] is set to [V-Log].
[SDI OUT V-Log]
Sets the output image from the <SDI OUT> terminal when the [SYSTEM] menu → [COLOR SETTING] is set to [V-Log].
[V‑Log] Outputs in same color as the recording image.
[V-709] Outputs in a converted color equivalent to standard CINE-LIKE. Setting suitable for a preview.
(Factory setting: [V-Log])
@@
NOTE
t The setting is xed to [V-709] when set to the following menu.
‑ [SYSTEM] menu → [REC FORMAT] → [480-59.94i/AVCHD SA]
‑ [SYSTEM] menu → [REC FORMAT] → [576-50.00i/AVCHD SA]
‑ [VIDEO OUT/LCD/VF] menu → [SDI OUT] → [OUT FORMAT] → [720×480i]
‑ [VIDEO OUT/LCD/VF] menu → [SDI OUT] → [OUT FORMAT] → [720×576i]
t This cannot be set when the [SYSTEM] menu → [COLOR SETTING] is set to [NORMAL].
[HDMI OUT]
[OUT FORMAT]
Selects the signal to output from the <HDMI> terminal. The items that can be selected differ depending on the [SYSTEM] menu → [FREQUENCY]/[FILE
FORMAT]/[REC FORMAT] setting.
[3840×2160p] Outputs in 3840×2160p (4:2:2/10-bit).
[3840×2160p(420/8bit)] Outputs in 3840×2160p (4:2:0/8-bit).
[1920×1080p] Outputs in 1920×1080p.
[1920×1080i] Outputs in 1920×1080i.
[1280×720p] Outputs in 1280×720p.
[720×480p] Outputs in 720×480p.
[720×576p] Outputs in 720×576p.
(Factory setting: [1920×1080p])
@@
NOTE
t For the combinations that can be set, refer to “Format that can be output from the <HDMI> terminal” (page 164).
[HDMI TC OUT]
Sets if the time code information is output or not in the output from the <HDMI> terminal.
The items that can be set are as follows.
f [ON], [OFF]
(Factory setting: [OFF])
[HDMI REC REMOTE]
Sets if the recording operation against the external equipment connected to the <HDMI> terminal (such as recorder) is to be controlled or not. This can
be set when [HDMI TC OUT] in [HDMI OUT] is enabled.
[ON] Controls the recording operation of the external equipment.
[OFF] Does not control the recording operation of the external equipment.
(Factory setting: [OFF])
@@
NOTE
t This cannot be set when the [RECORDING] menu → [REC FUNCTION] → [REC MODE] is set to [INTERVAL].
[HDMI OUT CHAR]
Sets whether to superimpose the character to the output from the <HDMI> terminal.
[ON] Superimposes.