Panasonic DMR-EZ48V

75
RQT9127
VHS Picture
VHS Sound
VHS Recording, Timer Recording
VHS Play
Operation Page
Cannot operate the television.
The remote control doesn’t work.
≥Change the manufacturer code. Some televisions cannot be operated even if you change the
code.
≥The remote control and main unit are using different codes. Change the code on the remote
control.
Press and hold [OK] and the indicated number button at the same time
for more than 5 seconds.
≥The batteries are depleted. Replace them with new ones.
≥You are not pointing the remote control at the main unit’s remote control signal sensor during
operation.
≥Coloured glass may obstruct the signal reception/transmission.
≥Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight
exposure.
≥It may be necessary to set the code on the remote control again after changing the batteries.
≥It may be necessary to set the manufacturer code again after changing the batteries.
≥The child lock function is activated.
66
64
4
4
—
—
64
66
66
Cannot operate the DVD. ≥Press [DRIVE SELECT] to select the DVD drive when operating DVDs or CDs. 16
Cannot operate the VHS. ≥Press [DRIVE SELECT] to select the VHS drive when operating video cassettes. 17
The unit is on but cannot be
operated.
≥Recording drive or playback drive has not been selected properly.
≥Some operations may be prohibited by the disc.
≥The unit is hot (“U59” appears on the display). Wait for “U59” to disappear.
≥One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1 Press [Í/I] on the main unit to switch the unit to standby.
If the unit doesn’t switch to standby, press and hold [Í/I] on the main unit for about
10 seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC mains lead, wait one minute, then reconnect it.
2 Press [Í/I] on the main unit to switch it on. If the unit still cannot be operated, consult the
dealer.
16, 17
—
—
—
Cannot eject disc. ≥The unit is recording.
≥The unit may have a problem. While the unit is off, press and hold [∫] and [CH W] on the
main unit at the same time for about 5 seconds. Remove the disc and consult the dealer.
If the Child Lock function is activated, above operation does not work. Cancel the Child Lock
function.
—
66
Cannot tune channels.
Cannot download channel
presets from the television.
≥Check the connections.
≥You must connect to a VIERA Link (HDAVI Control 3) compatible TV with a HDMI cable to
download channel presets.
8
—
Startup is slow. ≥Make sure that “Quick Start” is set to “On”.
≥Startup takes time in the following situations:
– A disc other than a DVD-RAM is inserted.
– The clock is not set.
– Immediately after a power failure or the AC mains lead is connected.
– When the unit is connected with an HDMI cable.
64
—
On-screen display indicators do
not appear.
≥Select a setting other than “Off” in “On-Screen Messages” in the Setup Menu.
–Press [STATUS ] to show the on-screen display indicators.
35, 62
The grey background appears
during play.
≥You are playing a blank or poor quality part of the video cassette.
≥You can damage the unit if you play dirty or damaged video cassettes and this can cause the
grey background to appear. Consult your dealer.
—
—
Cannot hear the desired audio
type.
≥Press [AUDIO] to select the audio. 35
There is noise when playing a
video cassette.
≥Adjust the tracking.
≥The tape is old or damaged.
35
—
“1” flashes when I try to start
recording.
Cannot record.
≥A video cassette is not inserted. Insert a video cassette with an intact accidental erasure
prevention tab.
≥The erasure prevention tab has been removed. Cover the hole with adhesive tape.
14
14
Cannot record TV programme. ≥The desired channel is not selected. Select the desired TV programme. —
Playback does not work properly. ≥The video head is dirty.
≥The tape is too old or damaged.
≥Check the “SQPB” setting.
≥The video heads are clogged or worn: consult your dealer.
5
—
34
—
Troubleshooting guide
DMREZ48VGN-RQT9127-L_eng.book 75 ページ ２００８年５月７日 水曜日 午前９時２８分