Panasonic MCD Series - Motor and Brake Connector Wiring

−
B23
−−
B22
−
English
3. System Conguration and Wiring
Wiring Diagram
XC
XB
Motor
ALM+
L2
L3
L1C
L2C
MC
MCCB
L1
ALM−
XA
X4
L
ON
B1
B3
B2
NC
U
V
W
Motor
ALM+
L2
L3
L1C
L2C
MC
MCCB
L1
ALM−
X4
L
ON
B1
B3
B2
NC
U
V
W
ALM
OFF
MC
ALM
OFF
MC
Noise filter
Red
White
Black
Green
Main power
supply
Control power
supply
Motor
connection
Main power
supply
Control power
supply
Motor
connection
Noise filter
Red
White
Black
Green
Coil surge suppression units
Coil surge suppression units
37
36
ALM
Insulated
DC12 to 24 V
(±5 %)
+
−
37
36
ALM
Insulated
DC12 to 24 V
(±5 %)
+
−
* These colors
are used for
optional cable.
* These colors
are used for
optional cable.
Built-in thermostat of an external
regenerative resistor (light yellow)
Built-in thermostat of an external
regenerative resistor (light yellow)
Power supply 3-phase,
200 V
–15 %
to 230 V
+10 %
In Case of 3-Phase,
E-frame, 200 V type
Power supply 3-phase,
200 V
–15 %
to 230 V
+10 %
In Case of 3-Phase,
F-frame, 200 V type
External
regenerative
resistor
(Note 1) Shorting cable
External
regenerative
resistor
(Note 1) Short bar
Note
Forwiringthemotorconnector,refertoP.B21.
3. System Conguration and Wiring
Wiring of connector for motor and brake
•Whenthe motors of
<MSME (50 W to 750 W)>
areused,theyare connected as
shownbelow.
 Connector:MadebyJapanAviationElectronicsIndustry,Ltd.
 (Theguresbelowshowconnectorsforthemotor.)
•Whenthemotorsof
<MSME (1.0 kW to 5.0 kW), MDME, MFME, MGME, MHME>

areused,theyareconnectedasshownbelow.
 Connector:MadebyJapanAviationElectronicsIndustry,Ltd.
 (Theguresbelowshowconnectorsforthemotor.)
Composethecircuitsothatthemaincircuitpowerwillbeshutoffwhenanerroroccurs.
JN8AT04NJ1
1
U-phase
V-phase
W-phase
Ground
PIN No.
2
3
PE
Application
PE
3
2
1
1
2
<Motor> <Brake>
JN4AT02PJ1-R
Tightening torqueof
the screw (M2)
0.085 to 0.095 N·m
(screwed to plastic)
Tightening torqueof
the screw (M2)
0.19 to 0.21 N·m
1
2
Brake
Brake
PIN No.
Application
* Be sure to use only the screw supplied with the connector, to avoid damage.
Do not connect anything to NC.
Remarks
A
B
D
C
AHG
CDE
BIF
CBA
IHG
FED
A
JL04V-2E20-4PE-B-R
JL04HV-2E22-22PE-B-R
JL04V-2E20-18PE-B-R
JL04V-2E24-11PE-B-R
U-phase
V-phase
W-phase
Ground
PIN No.
B
C
D
Application
G
H
A
F
I
B
E
D
C
Brake
Brake
NC
U-phase
V-phase
W-phase
Ground
Ground
NC
PIN No.
Application
A Brake
Brake
NC
U-phase
V-phase
W-phase
Ground
Ground
NC
PIN No.
B
C
D
E
F
G
H
I
Application
AHG
CDE
BIF
CBA
IHG
FED
JL04V-2E20-18PE-B-R
JL04V-2E24-11PE-B-R
G
H
A
F
I
B
E
D
C
NC
NC
NC
U-phase
V-phase
W-phase
Ground
Ground
NC
PIN No.
Application
A NC
NC
NC
U-phase
V-phase
W-phase
Ground
Ground
NC
PIN No.
B
C
D
E
F
G
H
I
Application
<without Brake> <with Brake>
(Note1)
Frame
Shorting
cable
(Accessories)
Internal
regenerative
resistor
ConnectionoftheconnectorXC
Incaseofusing
theexternalregenerativeresistor
Incaseofnotusing
theexternalregenerativeresistor
E-frame With With
BetweenB2andB3:
Disconnecttheshortingcable
BetweenB1andB2:
Connecttheexternalregenerativeresistor
BetweenB2andB3:
Connecttheshortingcable
Frame
Shortbar
(Accessories)
Internal
regenerative
resistor
Connectionofterminalblock
Incaseofusing
theexternalregenerativeresistor
Incaseofnotusing
theexternalregenerativeresistor
F-frame With With
BetweenB2andB3:
Disconnecttheshortbar
BetweenB1andB2:
Connecttheexternalregenerativeresistor
BetweenB2andB3:
Connecttheshortbar