Panasonic S-36MK2E5A - Page 105

3-29
Control of VRF SYSTEM
1
2
3
4
5
6
7
8
9
2. Instrallation Instractions
12
(EN)
Setting
 RC. setting mode (Main/sub, Clock type, Password change)  Detailed settings
(Vent output setting, Temp sensor setting, Temp display
setting)
1
Press and hold the 3 buttons for 4 seconds or more simultaneously.
, , Ź
2
Select the item to set. Ÿ ź ĺ
RC. setting mode
3
Set. (Select the Code no. and Set data.) Ÿ ź ĺ Ź ĺ
(Repeat)
Code no. Set data
Code no.
Set data
01 Main/sub
Set this when using 2 remote controllers.
• 0000: Sub • 0001: Main (factory
setting)
02 Clock type Set the type of clock display.
• 0000: 24 hours • 0001: 12 hours
(AM/PM)
2F
Password change
Set the administrator password.
• 0000 to 9999 • 0000 (factory setting)
Detailed settings
3
Set. (Select the indoor unit number, Code no. and Set data.) Ÿ ź ĺ Ź ĺ
(Repeat)
Indoor unit number
Set data
Code no.
Code no.
Set data
31
Vent output setting
Set this when connecting a commercially sold fan, etc. to the ventilation fan output “FAN DRIVE:2P (White)” on the indoor control board. *Dedicated cables (optional) are required.
• 0000: Not connected • 0001: Connected
32
Temp sensor setting
Set this when measuring the room temperature with the room temperature sensor of the remote controller. • When using the main and sub controllers, the main one is
enabled.
• When controlling in group, set this for the main indoor unit number.
(No setting is required for sub indoor units.)
• When using with the remote sensor in combination, set the indoor
unit setting data.
• 0000: Indoor unit • 0001: RC
33
Temp display setting
Set the type of temperature display.
• 0000: °C • 0001: °F
業務用リモコンCZ-RTC3据付書En.indd12 2014/01/2414:25:07
13
(EN)
Setting
 Auto address  Set elec. consumption
Auto address
3
Set. (Select the Code no. [A1] and O/D unit no.) Ÿ ź ĺ Ź ĺ
(Repeat)
Code no. O/D unit no.
Code no.
O/D unit no.
A1
Set the Auto address for each O/D unit no. Select the O/D unit no. (outdoor unit) for Auto address.
• Outdoor unit number
Note
z After RC. setting mode, Detailed settings or Auto address is complete, the unit
restarts.
Attention
z Set Auto address after all units are turned on and 1 minute and 30 seconds or
more have passed.
z Operate the units after Auto address is set and 1 minute and 30 seconds or more
have passed.
Set elec. consumption
3
Set. (Select the power supply voltage of outdoor units.) Ÿ ź ĺ
Note
z Set the power supply voltage of outdoor units to calculate electric consumption of
the
Power consumption monitor.
z If the setting differs from the power supply voltage of outdoor units, the electricity
display error may occur.
z Depending on the outdoor unit model, this cannot be set.
 When 3-phase model connections are used for outdoor units
Power supply voltage Setting value
380 V 220 V 400 V 230 V 415 V 240 V
ENGLISH
業務用リモコンCZ-RTC3据付書En.indd13 2014/01/2414:25:07
TD831172-00VRFSYSINDOOR.indb29TD831172-00VRFSYSINDOOR.indb29 2014/06/1316:54:492014/06/1316:54:49