182
RS-232 Adjustment Mode
P PUS PURECINEMA STANDARD ‡ ×××Sets PURECINEMA to STANDARD.
PWL POWER CONTROL MODE1 ‡ ×××Sets power control setting to MODE1 (power-saving).
PWN
POWER CONTROL STANDARD
‡ ×××Sets power control setting to STANDARD.
PWS POWER CONTROL MODE2 ‡ ×××
Sets power control setting to MODE2 (low deterioration).
PWY PC WIDE YES ‡ ×××Sets input setting to wide (SETTING: WVGA or WXGA).
R RHI R HIGH ‡ × ‡‡Adjusts RED HIGH-LIGHT.
RLW R LOW ‡ × ‡‡Adjusts RED LOW-LIGHT.
RSL R SIDE MASK LEVEL ‡ × ‡‡Adjusts RED SIDE MASK LEVEL.
S SCM COLOR SYSTEM SECAM ‡ ×××Sets COLOR SYSTEM setting to SECAM.
SHP H.SHARP ‡ × ‡‡Adjusts H.SHARP/H.ENHANCE.
SHV V.SHARP ‡ × ‡‡Adjusts V.SHARP/V.ENHANCE.
SLN STILL NO ¶¶××Releases image from stillness.
SLY STILL YES ¶¶××Makes image still.
SM0 SCREEN MODE 0 ‡‡××Sets screen size to DOT BY DOT.
SM1 SCREEN MODE 1 ‡‡××Sets screen size to 4:3.
SM2 SCREEN MODE 2 ‡‡××Sets screen size to FULL.
SM3 SCREEN MODE 3 ‡‡××Sets screen size to ZOOM/PARTIAL.
SM5 SCREEN MODE 5 ‡‡××Sets screen size to WIDE.
STD STANDARD W/B ‡ ×××
Initializes image quality and white balance adjustment data.
SV1
(NOTE)
SUB VOLUME INPUT1 ‡ × ‡‡Adjusts sub-volume. for INPUT1.
SV2
(NOTE)
SUB VOLUME INPUT2 ‡ × ‡‡Adjusts sub-volume. for INPUT2.
SV3
(NOTE)
SUB VOLUME INPUT3 ‡ × ‡‡Adjusts sub-volume. for INPUT3.
SV4
(NOTE)
SUB VOLUME INPUT4 ‡ × ‡‡Adjusts sub-volume. for INPUT4.
SV5
(NOTE)
SUB VOLUME INPUT5 ‡ × ‡‡Adjusts sub-volume. for INPUT5.
T TNT TINT ‡ × ‡‡Adjusts TINT.
TVA COLOR SYSTEM AUTO ‡ ×××Sets COLOR SYSTEM to AUTO.
U UP0 UP10 ‡ × – – Increases adjustment value by 10.
UP n UPn ‡ × – – Increases adjustment value by n.
UPF UP FULL ‡ × – – Maximizes adjustment value.
V VOL VOLUME ‡‡‡‡Adjusts audio volume.
VPS VERTICAL POSITION ‡ × ‡‡Adjusts vertical position.
VRO VARIABLE OUTPUT ‡ ×××Makes sound output variable.
VSI VERTICAL SIZE ‡ × ‡‡Adjusts vertical size.
Y YCM 3D Y/C MOTION ‡ ×××Sets 3D Y/C to MOTION.
YCS 3D Y/C STILL ‡ ×××Sets 3D Y/C to still.
Function
Command
Name
Full Name
RS-232C
Adjustment
Validity
Normal
Validity
Numerical
Direct
Validity
Up/Down
Validity
(NOTE) Make sure to use commands for adjusting sub-volume (SV1~5) after first switching to the prescribed input using the input
switching commands (IN1~5).
To Next Page
Loading...
