PDP-507CMX
174
1234
1234
C
D
F
A
B
E
Command Operation
Command Effectiveness Numeric Direct input
Remarks
Factory
Normal
Operation
Validity Minimum Maximum
Various adjustment of the panel side
ABL*** Adjusting the power upper limit value (ABL) O - O 000 255
PRH*** Adjusting the R HIGH of panel W/B O - O 000 511
PGH*** Adjusting the G HIGH of panel W/B O - O 000 511
PBH*** Adjusting the B HIGH of panel W/B O - O 000 511
PRL*** Adjusting the R LOW of panel W/B O - O 000 999
PGL*** Adjusting the G LOW of panel W/B O - O 000 999
PBL*** Adjusting the B LOW of panel W/B O - O 000 999
VOF*** Adjusting the offset voltage O - O 000 255
VRP*** Adjusting the P-RST voltage O - O 000 255
VSU*** Adjusting the sus voltage O - O 000 255
RSW*** Adjusting the XY-RST width 1 O - O 120 136
RYW*** Adjusting the XY-RST width 2 O - O 120 136
PGMS** Set up the panel gamma table O O - - -
XSB*** Adjusting the X-SUS B timing O - O 120 136
YSB*** Adjusting the Y-SUS B timing O - O 120 136
YTG*** Adjusting the Y-SUS TAIL timing O - O 120 136
YTW*** Adjusting the Y-SUS TAIL width O - O 120 136
Various control of the panel side
PKLS00 Setting the brightness to 0 O O - - -
PKLS01 Setting the brightness to 1 O O - - -
PKLS02 Setting the brightness to 2 O O - - -
PKLS03 Setting the brightness to 3 O O - - -
PKLS04 Setting the brightness to 4 O O - - -
PKLS05 Setting the brightness to 5 O O - - -
PKLS06 Setting the brightness to 6 O O - - -
PKLS07 Setting the brightness to 7 O O - - -
PWAS00 Setting the power consumption to normal O O - - - 507CMX : 4L, 607CMX : 2L
507CMX : 4L, 607CMX : 2L
PWAS01
Setting the power consumption to energy-saving
OO - - -
PWAS10 Setting the power consumption to normal (2L) O O - - -
PWAS11
Setting the power consumption to energy-saving (2L)
OO - - -
SMMS** Setting the side mask to full screen O O - - -
SQMS00
Setting the drive sequence mode to sequence at no signal input
OO - - -
SQMS01
Setting the drive sequence mode to sequence for VIDEO (animation)
OO - - -
SQMS02
Setting the drive sequence mode to sequence for PC (still picture)
OO - - -
SQMS03
Setting the drive sequence mode to 48Hz/72Hz sequence
OO - - -
WBIS00 Turning the default output of panel W/B off O - - - -
WBIS01 Turning the default output of panel W/B on O - - - -
APWS00 Prohibiting WB-APL interlocking O - - - -
APWS01 Permitting WB-APL interlocking O - - - -
Mask indication
VFQS01
Setting the frequency in mask mode to VIDEO-48Hz
O ----
VFQS02
Setting the frequency in mask mode to VIDEO-50Hz
O ----
VFQS03
Setting the frequency in mask mode to VIDEO-60Hz
O ----
VFQS05
Setting the frequency in mask mode to VIDEO-72Hz
O ----
VFQS06
Setting the frequency in mask mode to VIDEO-75Hz
O ----
VFQS13 Setting the frequency in mask mode to PC-60Hz O - - - -
VFQS14 Setting the frequency in mask mode to PC-70Hz O - - - -
To Next Page
Loading...
