Power Electronics SD700 User Manual

POWER ELECTRONICS
SD700FR SERIES
MODBUS COMMUNICATION
69
Parameter
Screen
Description
Address
Range
Modbus
Range
G11.7
7 HI V TO=5s
Trip time because of high input voltage
40460
0.0 to 60s, OFF
0 to 600; 610
G11.8
8 Dlasy VO = 5s
Trip delay time due to output voltage imbalance
40463
0.0s to 10s; OFF
0 to 100; 101
G11.9
9 LOW V BHV=1
Performance in case of input power loss
40461
1 to 3
1 to 3
G11.10
10 PTC EXT ?=N
PTC motor option
40462
N
Y
0 to 1
G11.11
11 PUMP OV=20.0A
Pump overload level
40289
0.0 to 3000A
0 to 30000
G11.12
12 PMovl FIL=OFF
Filter for pump overload
40290
OFF=0; 0.1 to 20.0s
0 to 200
G11.13
13 Povl DLY=OFF
Trip delay time because of pump overload
40291
OFF=0; 1 to 999.9s
0 to 9999
G11.14
14 UNDERLOAD=N
To enable underload protection
42085
N
Y
0 to 1
G11.15
15 ULD CUR=___A
Underload current
42086
(0.2 to 1.50)·In
0 to 12288
G11.16
16 ULD SPD=+100%
Underload speed
42087
+0.0% to +250%
0 to 20480
G11.17
17 ULD DELY=10s
Delay time to activate underload protection
42088
0 to 999s
0 to 9999
G11.18
18 DEC.SPdly=OFF
Speed decreasing delay time
40599
OFF=0, 1 to 10s
0, 1 to 10
G11.19
19 Sp.SRCH.I =10%
Increasing of speed searching
40464
2 to 40%·In
164 to 3276
G11.21
21 Vc Min. T = OFF
Minimum speed limit
40466
0.0 to 60.0, OFF
0-610
G11.22
22 Rdsq ls = 5.0s
Sets delay time before the trip.
40467
0.0 to 10.0, OFF
0-101
G12.1
1 AUTO RESET=N
Auto Reset
40571
N
Y
0 to 1
G12.2
2 ATTEMP NUMBR=1
Number of Auto Reset attempts
40572
1 to 5
1 to 5
G12.3
3 R STR DEL=5s
Delay time before Auto Reset
40573
5 to 120s
5 to 120
G12.4
4 RS COUNT=15min
Reset time counter of Auto Reset attempts
40574
1 to 60min
1 to 60
G12.5
5 F1 AUTO RST=0
Selection of fault 1 to be reset
40575
0 to 27
0 to 27
G12.6
6 F2 AUTO RST=0
Selection of fault 2 to be reset
40576
0 to 27
0 to 27
G12.7
7 F3 AUTO RST=0
Selection of fault 3 to be reset
40577
0 to 27
0 to 27
G12.8
8 F4 AUTO RST=0
Selection of fault 4 to be reset
40578
0 to 27
0 to 27
G13.1
1 F0 NO FAULT
Register 1 of fault history
40432
-
-
G13.2
2 F0 NO FAULT
Register 2 of fault history
40433
-
-
G13.3
3 F0 NO FAULT
Register 3 of fault history
40434
-
-
G13.4
4 F0 NO FAULT
Register 4 of fault history
40435
-
-
G13.5
5 F0 NO FAULT
Register 5 of fault history
40436
-
-
G13.6
6 F0 NO FAULT
Register 6 of fault history
40437
-
-
G13.7
7 CLEAR FAULTS=N
G13.7 / Erase fault history
40438
N
Y
0 to 1
G14.1
1 MREF 1=+10.0%
Multi-reference 1
40052
-250% to +250%
-20480 to
+20480
G14.2
2 MREF 2=+20.0%
Multi-reference 2
40053
-250% to +250%
-20480 to
+20480
G14.3
3 MREF 3=+30.0%
Multi-reference 3
40054
-250% to +250%
-20480 to
+20480
G14.4
4 MREF 4=+40.0%
Multi-reference 4
40055
-250% to +250%
-20480 to
+20480
G14.5
5 MREF 5=+50.0%
Multi-reference 5
40056
-250% to +250%
-20480 to
+20480
G14.6
6 MREF 6=+60.0%
Multi-reference 6
40057
-250% to +250%
-20480 to
+20480
G14.7
7 MREF 7=+70.0%
Multi-reference 7
40058
-250% to +250%
-20480 to
+20480
G15.1
1 INCH1=+0.00%
Inch speed 1
40092
-250% to +250%
-20480 to
+20480
G15.2
2 INCH2=+0.00%
Inch speed 2
40093
-250% to +250%
-20480 to
+20480
G15.3
3 INCH3=+0.00%
Inch speed 3
40094
-250% to +250%
-20480 to
+20480
G16.1
1 SKIP 1=+0.0%
Skip frequency 1
40132
-250% to +250%
-20480 to
+20480
G16.2
2 SKIP 2=+0.0%
Skip frequency 2
40133
-250% to +250%
-20480 to
+20480
G16.3
3 SKIP BAND=OFF
Skip bandwidth
40134
OFF=0 to 20%
0 to 1638
G17.1
1 T DC BRAKE=OFF
Time for DC brake activation
40025
OFF=0.0 to 99s
0 to 990
G17.2
2 DC CURR=0%
Current applied to the brake
40022
0 to 100%
0 to 8192
G17.3
3 DC VOLTS=0.0%
Voltage applied to the brake
40023
0.0 to 25%
0 to 2048
G17.4
4 I HEATING=OFF
Non condensing heating current
40024
OFF=0.0 to 30%
0 to 2458

Power Electronics SD700 Specifications

General

Brand	Power Electronics
Model	SD700
Category	Inverter
Language	English