Rabbit Smartcat - Page 131

User’s Manual 125
hardware ............................13
reset generator ...................76
RS-232 ..................................23
RS-485 ..................................23
RS-485 network ....................24
termination and bias resistors
25
S
sample programs ...................38
A/D converter
AD_CALIB.C ...............39
AD1.C ...........................39
AD2.C ...........................39
AD3.C ...........................39
AD4.C ...........................39
calibration constants
GETCALIB.C ... 29, 30, 40
SAVECALIB.C 29, 30, 40
D/A converter
DACAL.C .....................39
DAOUT1.C ...................39
DAOUT2.C ...................40
digital I/O
DIGIN.C ........................38
DIGOUT.C ....................38
PWM.C .........................38
how to set IP address ........57
LCD/keypad module ...40, 90
ALPHANUN.C .............90
COFTERMA.C .............90
DISPPONG.C ...............90
DKADEMO1.C .............90
FUN.C ...........................90
KEYBASIC.C .........82, 90
KEYMENU.C ...............90
LED.C ...........................90
SCROLLING.C ............90
TEXT.C .........................90
LCD/keypad module (with
TCP/IP)
MBOXDEMO.C ...........91
TCP_RESPOND.C .......91
TCPSEND.C .................91
PONG.C ............................15
real-time clock
RTC_TEST.C ................40
SETRTCKB.C ..............40
serial communication
MASTER.C ...................39
PUTS.C .........................38
RELAYCHR.C .............38
SLAVE.C ......................39
TCP/IP ........................40, 57
PINGME.C ....................59
SMTP.C ........................60
SSI.C .............................60
TELNET.C ....................60
serial communication ............23
flow control .......................45
function calls
ser485Rx .......................45
ser485Tx .......................45
serCflowcontrolOff ....... 45
serCflowcontrolOn ........45
serMode .........................45
programming port .............27
RS-232 description ........... 23
RS-485 description ........... 23
RS-485 network ................24
RS-485 termination and bias
resistors .........................25
serial ports
Ethernet port .....................26
setup ........................................ 9
attach BL2100 to enclosure
base ...............................10
power supply connections . 13
programming cable connec-
tions ..............................12
reconnect RabbitCore module
11
remove RabbitCore module 9
software ..................................5
LCD/keypad module LEDs ..
92
libraries .............................41
BL2100 .........................41
BL21xx.LIB ..................41
PACKET.LIB ................45
RS232.LIB ....................45
TCP/IP ........................... 41
macros
USE_2NDFLASH_CODE
35
sample programs ...............38
specifications
BL2100
electrical ........................63
exclusion zone ............... 64
header footprint .............65
headers ..........................65
relative pin 1 locations .. 65
temperature ...................63
dimensions (BL2100 main
board) ............................62
LCD/keypad module
dimensions ....................79
electrical ........................ 80
header footprint ............. 80
mechanical .................... 80
relative pin 1 locations .. 80
temperature ................... 80
plastic enclosure
dimensions ..................116
spectrum spreader .................34
subsystems ............................ 17
T
TCP/IP connections .............. 55
10Base-T Ethernet card .... 55
additional resources ..........60
Ethernet hub ......................55
steps .................................. 55
technical support ...................16
Tool Kit ...................................4
AC adapter .......................... 4
DC power supply ................4
Demonstration Board ..........4
Dynamic C software ...........4
plastic enclosure .................. 4
programming cable ............. 4
software ............................... 4
User’s Manual .....................4
wire assembly ..................... 4
troubleshooting
changing COM port .......... 15
connections ....................... 15
U
USB/serial port converter ..... 12
Dynamic C settings ........... 15