Rabbit Smartcat - Page 130

124 Smartcat (BL2100)
how to set PC IP address ...58
J
jumper configurations .....67, 68
Demonstration Board .....120,
121, 122
digital inputs ......................68
JP1 (RS-485 bias and termina-
tion resistors) ...........25, 68
JP2 (configure IN16–IN23 as
digital inputs or outputs) 68
JP2 (flash memory bank se-
lect) ...............................32
jumper locations ................67
K
K ............................................21
keypad template ....................82
removing and inserting label .
82
L
LCD/keypad module ...............3
bezel-mount installation ....87
contrast adjustment ............81
dimensions .........................79
header pinout .....................83
I/O address assignments ....83
keypad
function calls
keyConfig ................109
keyGet ......................110
keyInit ......................109
keypadDef ................111
keyProcess ...............110
keyScan ....................111
keyUnget ..................110
keypad template .................82
LCD display
function calls
glBackLight ...............93
glBlankScreen ............94
glBlock .......................94
glBuffLock ...............100
glBuffUnlock ...........100
glDispOnOff ..............93
glDown1 ..................103
glFillCircle .................97
glFillPolygon .............96
glFillScreen ................94
glFillVPolygon ..........96
glFontCharAddr .........98
glGetBrushType .......101
glGetPfStep ................99
glHScroll ..................104
glInit ..........................93
glLeft1 .....................102
glPlotCircle ................96
glPlotDot ..................101
glPlotLine ................102
glPlotPolygon ............95
glPlotVPolygon .........95
glPrintf .....................100
glPutChar ...................99
glPutFont ...................98
glRight1 ...................102
glSetBrushType .......101
glSetContrast .............94
glSetPfStep ................98
glSwap .....................101
glUp1 .......................103
glVScroll ..................105
glXFontInit ................97
glXPutBitmap ..........105
glXPutFastmap ........106
TextCursorLocation .107
TextGotoXY ............107
TextPrintf .................108
TextPutChar .............108
TextWindowFrame ..106
LDEs
function calls
ledOut ........................92
mounting instructions ........84
mounting locations ............65
remote cable connection ....89
removing and inserting keypad
label ...............................82
removing and plugging in pro-
gramming cable .......85, 86
sample programs ...............90
versions .............................79
M
memory .................................32
flash memory configurations .
32
SRAM configuration for dif-
ferent sizes ....................32
models .....................................2
BL2100 ................................2
BL2110 ................................2
BL2120 ................................2
BL2130 ................................2
connector options ................2
mounting instructions
LCD/keypad module .........84
O
options .....................................3
connectors ...........................2
LCD/keypad module ...........3
plastic enclosure ..................3
P
pinout
BL2100 headers ................18
Ethernet port ......................26
LCD/keypad module .........83
plastic enclosure ..............4, 113
assembly instructions ......114
attach BL2100 to base .......11
dimensions .......................116
mounting instructions ......116
setup
attach BL2100 to enclosure
base ...........................114
attaching top ................116
install LCD/keypad module
115
reconnect RabbitCore mod-
ule .............................115
remove RabbitCore module
114
power management ...............73
power supply .........................73
backup battery circuit ........75
battery backup ...................74
chip select circuit ...............77
connections ........................13
switching voltage regulator 73
VRAM switch ...................76
programming
flash vs. RAM ...................35
programming cable ..............4
programming port ..............27
programming cable .................4
connections ........................12
PROG connector ...............28
switching between Program
Mode and Run Mode ....28
use when LCD/keypad module
installed ...................85, 86
programming port .................27
R
Rabbit 2000
parallel ports ......................69
real-time clock
how to set ..........................40
reset .......................................13