Renkforce RF100 v2 - Connecting to Mains Power

10
• Donotmovetheproductduringoperation.Turnofftheproductbeforemoving,transportingorstoringit.
• Neverusethe3Dprinteroutdoors.
• Neverplacecontainerscontainingliquids,e.g.glasses,vases,etc.onthedeviceorinitsvicinityanddo
notpouranyliquidsoutoverthedevice.Liquidsmaygetintothehousingandimpairelectricalsafety.
Thisalsoposesgreatdangerofreorpotentiallyfatalelectricshock!
Ifthisisthecase,rstpowerdowntherespectivemainssocketonallpoles(e.g.switchoffcircuitbreaker
andFIswitch)andthenpullthemainscablefromthesocket.Disconnectalllinesfromthedevice.Donot
operateanypartoftheproductanymoreafterwards,buttakeittoaspecialistworkshop.
• Neverplaceanysourcesofopenre,suchaslitcandles,onorrightnexttothedevice.
• Neverconnectthemainsplugtoamainssocketimmediatelyafterthedevicehasbeentakenfromacold
toawarmenvironment.Theresultingcondensationmaydestroythedevice.Allowthedevicetoreach
roomtemperaturebeforeconnectingit.Waituntilthecondensationhasevaporated.
• Donotcovertheopeningsonthebottomoftheproduct.Donotinsertanysharpobjectsintotheproduct
asthismaycauseanelectricshock!
• Donotoperatetheproductunattended.
• Under nocircumstances should you serviceany of the componentsin the interior ofthe 3D printer
thereforeneverdisassemblethemotorunit.
• Whensettingupthe3Dprinter,observethatthemainsswitchattherearofthedevicemustbeeasyto
reachsothatthedevicecanbeswitchedoffquicklyandeasilyincaseofmalfunction.
• Inoperation,therewillbenoiseand,dependingonthelamentmaterialused,smells.Observethiswhen
selectingthesiteofsetupandthelamentmaterial.Ensuresufcientventilationorinstallanextraction
system.Donotinhalearisingvapours.Whenusinganyotherthantherecommendedlamentmaterial,
poisonousvapoursorgasesmaydevelop.
• Observetheadditionalsafetyinformationintheindividualchaptersoftheseinstructions.
• Forsafetyreasons,anyunauthorizedconversionsand/ormodicationstotheproductdeviatingfrom
these operating instructions are not permitted. Components may be damaged and thus impair the
functionorsafetyofthedevice.
• Consultanexpertwhenindoubtabouttheoperation,safetyorconnectionofthedevice.
• Maintenance,modicationsandrepairsaretobeperformedexclusivelybyanexpertorataqualied
shop.
• Ifyouhavequestionswhichremainunansweredbytheseoperatinginstructions,contactourtechnical
supportserviceorothertechnicalpersonnel.
b) Connecting the mains
• Thisdeviceisasafetyclass1product.Theonlypermissiblevoltagesourceisaproperlygroundedmains
socket(100–240V/AC,50/60Hz)ofthepublicmains.
• Beforeconnectingthe3Dprintertothemains,makesurethatyourlocalACmainsvoltagematchesthe
specicationsonthenameplate(onthebackofthe3Dprinter).
• Nevertouchthemainslineorthemainsplugwithwetordamphands.Thereisariskofpotentiallyfatal
electricshock!
• Donotletthepowercablehangovertheedgeoftablesorothersurfacesonwhichthe3Dprinteris
standing.