Rigol DS4024E - Appearance and Dimensions

To Next Page

To Previous Page

Chapter 1 Quick Start RIGOL

DS4000E User’s Guide 1-3

Appearance and Dimensions

Figure 1-1 Front View Unit: mm

Figure 1-2 Side View Unit: mm

Main Page

Guaranty and Declaration3
Safety Requirement4
- General Safety Summary4
- Safety Terms and Symbols6
- Allgemeine Sicherheits Informationen7
- Sicherheits Begriffe und Symbole9
- Measurement Category10
- Ventilation Requirement10
- Working Environment11
- General Care and Cleaning12
- Environmental Considerations13
DS4000E Series Overview14
Document Overview15
- Table of Contents18
Chapter 1 Quick Start25
- General Inspection26
- Appearance and Dimensions27
- To Prepare the Oscilloscope for Use28
- Front Panel Overview35
- Rear Panel Overview36
- Front Panel Function Overview38
- User Interface45
- To Use the Security Lock51
- To Use the Built-In Help System52
Chapter 2 Vertical System Setting55
- To Turn the Channel On/Off56
- To Adjust the Vertical Scale57
- To Adjust the Vertical Position58
- To Specify the Channel Coupling59
- To Specify the Bandwidth Limit60
- To Set the Probe60
- To Specify the Input Impedance65
- To Turn Waveform Invert On/Off66
- To Specify the Vertical Reference66
- To Specify the Amplitude Unit67
- To Set the Channel Label67
- To Set the Delay Calibration69
Chapter 3 Horizontal System Setting71
- To Adjust the Horizontal Time Base72
- To Adjust the Horizontal Position73
- To Specify the Time Base Mode74
- To Turn Delayed Sweep On/Off78
- To Specify the Horizontal Reference80
Chapter 4 Sample System Setting81
- Sample Mode82
- Sample Rate82
- To Specify the Acquisition Mode83
- To Set the Memory Depth86
- To Turn Anti-Aliasing On/Off87
Chapter 5 Trigger89
- Trigger Source90
- Trigger Level91
- Trigger Mode92
- Trigger Coupling94
- Trigger Holdoff95
- Noise Rejection96
- Trigger Output Connector96
- Edge Trigger97
- Pulse Trigger98
- Runt Trigger101
- Nth Edge Trigger105
- Slope Trigger107
- Video Trigger111
- Pattern Trigger114
- RS232 Trigger116
- I2C Trigger119
- SPI Trigger123
- CAN Trigger126
- Flexray Trigger131
- LIN Trigger (Option)133
- USB Trigger136
Chapter 6 Operations and Measurements139
- To Make Math Operation140
- To Make Auto Measurement158
- To Make Cursor Measurement174
Chapter 7 Protocol Decoding189
- Parallel Decoding190
- RS232 Decoding (Option)194
- I2C Decoding (Option)201
- SPI Decoding (Option)205
- CAN Decoding (Option)210
- Flexray Decoding (Option)215
- LIN Decoding (Option)220
Chapter 8 Reference Waveform225
- To Turn the Reference Waveform Channel On/Off226
- To Select the Current Reference Waveform Channel227
- To Set the Reference Waveform Color227
- To Select the Reference Waveform Source Channel228
- To Save and Display the Reference Waveform228
- To Adjust the Reference Waveform Display229
- To Export the Reference Waveform File229
- To Import from the Reference Waveform File230
Chapter 9 Pass/Fail Test231
- To Enable or Disable the Pass/Fail Test Function232
- To Start or Stop the Pass/Fail Test Operation232
- To Specify the Source233
- To Set the Test Mask233
- Screen Region Mode233
  - Screen Region Mode234
  - Cursor Region Mode235
- To Turn the Test Result Display On/Off237
- To Set the Output Form of Test Failure237
- To Save the Test Mask Range239
- To Load the Test Mask Range239
Chapter 10 Waveform Recording241
- To Record Waveform Using the "Record" Mode242
- To Record Waveform Using the "Open" Mode245
  - To Play Back the Waveform Recorded246
    - Manual Playback246
    - Auto Playback247
  - To Analyze the Recorded Waveform250
    - To Set the Template (Trace Mode)255
    - To Create the Pass/Fail Test Mask (Pass/Fail Test Mode)256
Chapter 11 Display Control257
- To Specify the Display Type258
- To Set the Persistence Time258
- To Set the Waveform Brightness260
- To Specify the Screen Grid Type260
- To Set the Grid Brightness260
- To Set the Menu Display Time261
Chapter 12 Store and Recall263
- Storage System264
- Storage Type265
- To Perform Internal Storage and Recall268
- To Perform External Storage and Recall269
- Disk Management271
- Factory278
Chapter 13 System Function Setting285
- Remote Interface Configuration286
- System-Related292
Chapter 14 Remote Control303
- Remote Control Via USB304
- Remote Control Via LAN308
- Remote Control Via GPIB310
Chapter 15 Troubleshooting313
Chapter 16 Specifications317
Chapter 17 Appendix325
- Appendix A: Accessories and Options325
- Appendix B: Warranty326
Index327

Rigol DS4024E - Appearance and Dimensions

Table of Contents

Related product manuals