57
DGM001519.01 UM Sirius CE/ROTW
dZKh>^,KKd/E'
Laser devices are designed to have the best performance and maximum safety. If the system does not work
properly, the following diagnostic table may assist in identifying the cause.
Turning the device key is not
producing any detectable
effect
x Plug not connected
x Main switch not turned on
x Emergency LASER STOP
activated
x Check for main input
x Deactivate Emergency LASER STOP
switch
Fluctuation of energy parameter
during laser radiation
x Wait a few seconds for
stabilization.
x Call the service
Serial port communication
fault
ͻdŚŝƐǁĂƌŶŝŶŐĂƉƉĞĂƌƐǁŚĞŶƚŚĞ
serial communication from PC to
microprocessor fails
x Restart the system
x Call service
ͻWŽǁĞƌƐƵƉƉůLJĞƌƌŽƌŽƌbroken
ͻŚĂƌŐĞƌĞƌƌŽƌŽƌďƌŽŬĞŶ
No correspondence between
displayed energy and
treatment effects and/or
decrease of laser efficacy
ͻ&ŝďĞƌ damaged
ͻůĂƐƚƐŚŝĞůĚŵŝƌƌŽƌďƌŽŬĞŶ
ͻŚĂŶŐĞĨŝďĞƌůĂƐƚƐŚŝĞůĚ
ͻĂůůƐĞƌǀŝĐĞ
ͻIncorrect shutter position
ͻ/ŶĐŽƌƌĞĐƚƐŚƵƚƚĞƌƉŽƐŝƚŝŽŶ
The remote interlock contacts
are open
ͻdŚĞĞdžƚ/ŶƚĞƌůŽĐŬŝƐŶŽƚĐŽŶŶĞĐƚĞĚ
or is poorly connected
ͻŽŶƚƌŽůĞdžƚ/ŶƚĞƌůŽĐŬĐŽŶŶĞĐƚŝŽŶ
ͻtƌŽŶŐƉĞĚĂůĐŽŶŶĞĐƚŝŽŶƐ
ͻWĞĚĂů;ƐͿƐŚŽƵůĚďĞƉƌĞƐƐĞĚ
at the right moment
ͻŶƚĞƌŝŶZĞĂĚLJŵŽĚĞĂŶĚƉƌĞƐƐƚŚĞ
footswitch
Blast shield wrong installation
ͻtƌŽŶŐďůĂƐƚƐŚŝĞůĚinstallation
ͻŚĞĐŬůĂƐƚƐŚŝĞůĚ
ͻĂůůƐĞƌǀŝĐĞ
Fiber not present/connected
ͻtƌŽŶŐĨŝďĞƌŝŶƐƚĂůůĂƚŝŽŶ
ͻŚĞĐŬƚŚĞĨŝďĞƌĐŽŶŶĞĐƚŝŽŶ
Fiber not identified by RFID
ͻtƌŽŶŐĨŝďĞƌŝŶƐƚĂůůĂƚŝŽŶ
ͻtƌŽŶŐĨŝďĞƌƚLJƉĞ
ͻŚĞĐŬƚŚĞĨŝďĞƌĐŽŶŶĞĐƚŝŽŶ
ͻŚĂŶŐĞĨŝďĞƌ
ͻdŚĞemission is too high or low
ͻRestart the system
ͻCall service
Critical Errors and Warnings appearing during start-up procedure
ͻDĞƐƐĂŐĞĂĨƚĞƌŶĞǁ&tƌĞůĞĂƐĞ
installation
ͻ&tŝƐƐƵĞƐ
ͻ^ŚƵƚĚŽǁŶĂŶĚƌĞƐƚĂƌƚ
ͻĂůůƐĞƌǀŝĐĞ
ͻShut down and restart
ͻĂůůƐĞƌǀŝĐĞ
To Next Page
Loading...