Roland FR-4X - Tuning-Related Parameters (Tuning)

75
Menu Options
Parameter Explanation/Value
Rec Att
(Rec Attenuation)
This specifies the audio attenuation level
when recording audio data.
(Default: Off )
Off
Medium
High
Func Sw
(Function Switch)
Press the [ENTER/YES] button to make
settings for the function switches.
&
“Function Switch” (p. 76)
SustainA
(Sustain A Routing)
Press the [ENTER/YES] button to make
settings for the Sustain A routing.
&
“Sustain A Routing” (p. 79)
SustainB
(Sustain B Routing)
Press the [ENTER/YES] button to make
settings for the Sustain B routing.
&
“Sustain B Routing” (p. 79)
FootCtrl
(MIDI Foot Controller)
Press the [ENTER/YES] button to make
settings for the MIDI Foot Controller.
&
“MIDI Foot Controller” (p. 80)
SpEQ R.H
(Speaker EQ Right Hand)
Press the [ENTER/YES] button to make
settings for the Speaker EQ Right Hand.
&
“Speaker EQ Right Hand” (p. 80)
SpEQ L.H
(Speaker EQ Left Hand)
Press the [ENTER/YES] button to make
settings for the Speaker EQ Left Hand.
&
“Speaker EQ Left Hand” (p. 81)
Noise
(Keyboard & Button Noise)
This parameter allows you to specify if
you want or not the typical noise that
Keyboard and Button board produce.
On, Off
(Default: On)
A/B Sw
(A/B Switch)
When pressing the right-register button
is selected again, the state of the A (1-7) /
B (8-14) selection is switched.
For example, when the register 4 of
A-side is selected, the register 11 of
B-side will be selected by pressing the
[4/11] button.
NOTE
When the organ part is selected, if you set
the “A/B Sw” to ON, you will not be able to
switch slow / fast of rotary effect.
Off, On
(Default: Off )
S-Up SET
(Start-Up SET)
This parameter allows you to specify
which Set should be loaded at power-on.
1–100
(Default: 1)
Parameter Explanation/Value
USB Drv
(USB Driver)
“Generic”: Choose this if you want to
use the standard USB driver that was
included with your computer.
“Original”: Choose this if you want to
use a USB driver downloaded from the
Roland website (www.roland.com).
(Default: Original)
* This setting is applied after you save
the change and turn the power of the FR-4x
off and on again.
Generic
Original
MIDI
Make MIDI-related settings for the FR-4x.
&
“MIDI” (p. 82)
Tuning-Related Parameters (Tuning)
Here you can make settings that are related to tuning.
The master tuning setting is saved in system area, and the
transpose setting is saved in the user program.
Scale tuning settings are saved in both the system area and the
user program.
&
“How to Save System Parameters” (p. 86)
&
“Saving an User Program” (p. 39)
Also be sure to read “Important Remark About Saving Your
Settings” (p. 45).
Parameter Explanation/Value
M. Tuning
(Master Tuning)
This parameter allows you to change the
FR-4x overall tuning.
415.3–440.0–466.2 [Hz]
Transpose
(Transpose)
This parameter allows you to transpose
all sections of the FR-4x.
-6–0–5 (F#–C–F)
S. TunTyp
(Scale Tune Type)
This parameter allows you to change
scale type.
&
“Scale (Tuning)” (p. 31)
Equal (Off)
User 1–3
Arabic 1–2
Just Major
Just Minor
Pythagorean
Mean-Tone
Werckmeister
Kirnberger