To Next PageTo Next PageWhat to do if Salon Systems T-Max® Mgr has no lights?
First, ensure the transformer is correctly plugged into both the wall and the power input of the T-Max® Mgr. Try a different outlet, and if using a surge suppressor or UPS, plug the T-Max® Mgr directly into the wall. Check your building's circuit breaker. Finally, use a voltmeter to check the transformer voltage, which should be 9VAC at the connection to the T-Max® Mgr.
What to do if Salon Systems T-Max® Manager won't start beds and shows strange characters?
If the T-Max® Mgr doesn't turn on beds and the display shows strange characters, it indicates the program is lost or corrupted. To fix this, go to the C:\> prompt and type ADNET C1. Once the ADNET Utility program is on the screen, press L, then press Y, followed by the Enter key.
General| Brand | Salon Systems |
|---|---|
| Model | T-Max Manager |
| Category | Personal Care Products |
| Language | English |
Lists included hardware for T-Max Mgr/Plus and 3A/F/I units.
Details technical specifications like power, dimensions, and maximum units for T-Max devices.
Lists necessary PC components and operating systems for system compatibility.
Guides physical connection of the system components, including beds and power.
Explains assigning unique numerical addresses to each T-Max unit for network identification.
Details how to set audio levels for room intercom communication for clarity.
Provides instructions for system cabling and connecting modular cables.
Details specific wiring and connections for the 3A/I/Master unit.
Details specific wiring and connections for the Mgr/Plus unit.
Details specific wiring and connections for the 3A/F/I units.
Manual address configuration process for individual 3A/F/I units.
Initial system configuration steps for the manager unit.
Overview of manual operation features, controls, and the display.
Steps for manual system setup, parameter adjustment, and security levels.
Procedure for initiating a tanning session manually via the control panel.
Steps to stop an active tanning session manually.
How to temporarily suspend a tanning session and resume it.
Explains the indicator for room cleaning status and how to clear it.
Methods to view the operational status of tanning beds using lights and displays.
Guides installation of the management software from disk.
Setup for connecting software to the manager unit, including COM port and timing settings.
Covers software operation, status screens, session management, and parameter adjustments.
Configures audio messaging features and recording of in-room messages.
Instructions for configuring the intercom system, including volume adjustment.
Procedure for initiating calls from the main console to tanning rooms.
Procedure for initiating calls from a tanning room to the main console.
Configuration for automatic bed power-off during intercom use based on parameter settings.
How the system manages multiple incoming intercom calls.
Procedure for activating an emergency alert and its system-wide impact.
Instructions for increasing the number of controlled tanning beds by adding units.
Information on using repeaters to extend system communication range.
Instructions for adding additional manager units to the system.
Step-by-step guide for installing the 3A/F/I unit.
How to adjust settings directly on the 3A/F/I unit via its interface.
Procedure for starting sessions when the unit operates standalone.
How to pause and resume sessions when the unit operates standalone.
How to cancel sessions when the unit operates standalone.
Managing the clean room indicator and feature settings.
Configuration for bed cool-down periods and its effect on sessions.
Description of monitoring devices for salon staff.
Information on the current sensing device for bed status monitoring.
Specific features and settings for high-pressure tanning beds.
Wiring instructions for external session start buttons.
Information about protective enclosures for the T-Max units.
Illustration of the 3A/F/I front panel layout.
Illustration of the 3A/I/Master front panel layout.
Diagram of rear connections and audio circuit board.
Shows jumper configurations for specific settings.
Diagram for connecting the Sentry™ device.
Wiring diagram for low-current beds with Sentry™.
Illustration of the Mgr/Plus front panel layout.
Diagram of Mgr/Plus rear connections and PCB layout.
Diagram showing typical system connectivity and cabling.
Illustrates various system setup examples and options.
Shows wiring details for modular cables used in the system.
Diagram for wiring an external push button for session control.
General troubleshooting steps for common system issues.
Lists error codes and their possible solutions for diagnosis.
Alphabetical listing of topics and their page numbers for quick reference.
