Samsung OfficeServ 7200-S User Manual

OfficeServ 7200-S INSTALLATION
TECHNICAL MANUAL PART 1 JANUARY 2011
TABLE OF CONTENTS
INSTALLATION SECTION
PART DESCRIPTION PAGE
1 PRE-INSTALLATION INFORMATION
1.1 SITE REQUIREMENTS .......................................................................................................... 1.1
1.2 GROUNDING CONDITIONS.............................................................................................. 1.2
1.3 POWER CONDITIONS ......................................................................................................... 1.4
1.4 UNPACKING AND INSPECTION ...................................................................................... 1.4
2 INSTALLING CABINET
2.1 SYSTEM INSTALLATION PROCEDURE .......................................................................... 2.1
2.2 SELECTING INSTALLATION METHOD ........................................................................... 2.1
2.3 INSTALLING IN A RACK ..................................................................................................... 2.1
2.4 INSTALLING ON A WALL .................................................................................................. 2.4
2.5 CONNECTING GROUND WIRES ...................................................................................... 2.8
3 INSTALLING AND REPLACING CARDS
3.1 CABINET CONFIGURATION.............................................................................................. 3.1
3.2 MP20S MODULES ............................................................................................................... 3.3
3.3 INTERFACE BOARDS/CARDS ......................................................................................... 3.10
3.4 DAUGHTERCARD MODULES ......................................................................................... 3.37
3.5 CONNECTING POWER FAIL TRANSFER ...................................................................... 3.43
4 CONNECTING EXTERNAL BATTERIES
4.1 CONNECTING EXTERNAL BATTERIES ........................................................................... 4.1
5 CONNECTING POWER
5.1 BEFORE CONNECTING POWER....................................................................................... 5.1
5.2 PROCEDURE FOR CONNECTING POWER .................................................................... 5.1
5.3 CONNECTING THE OS 7150 EXTERNAL PoE PSU SUPPLEMENTAL POWER
SUPPLY .............................................................................................................................................. 5.2
6 CONNECTING C.O. LINES
6.1 SAFETY PRECAUTIONS ...................................................................................................... 6.1
6.2 CONNECTING C.O. LINES .................................................................................................. 6.2
Home Page

Samsung OfficeServ 7200-S Specifications

General

VoIP Support	Yes
Supported Protocols	SIP, H.323
Power Supply	100-240 VAC, 50/60 Hz
Operating Temperature	0°C to 40°C
Humidity Range	10% to 90% non-condensing
Type	IP-PBX
Integrated Voicemail	Yes

Summary

Pre-Installation Information

1.1 Site Requirements

1.2 Grounding Conditions

Details proper grounding procedures and requirements for system safety and operation.

1.3 Power Conditions

1.4 Unpacking and Inspection

Installing Cabinet

2.1 System Installation Procedure

Step-by-step guide for installing the OfficeServ 7200-S cabinet.

2.2 Selecting Installation Method

2.3 Installing in a Rack

Details the procedure and cautions for mounting the cabinet inside a 19-inch rack.

2.4 Installing on a Wall

Explains the process and required tools for wall mounting the cabinet.

2.5 Connecting Ground Wires

Describes how to connect the external grounding wire to the system.

Installing and Replacing Cards

3.1 Cabinet Configuration

3.2 MP20S Modules

Covers setting switches, installing daughterboards, and installing the MP20S module.

3.3 Interface Boards/Cards

Explains how to install and replace various interface boards in cabinet slots.

3.4 Daughtercard Modules

Connecting External Batteries

4.1 Connecting External Batteries

Provides guidance and precautions for connecting external battery backup systems.

Connecting Power

5.1 Before Connecting Power

5.2 Procedure for Connecting Power

Details the steps for connecting AC power to the system's cabinet.

5.3 Connecting the OfficeServ 7150 External PoE PSU Supplemental Power Supply

Connecting C.O. Lines

6.1 Safety Precautions

6.2 Connecting C.O. Lines

Power Up Procedures

8.1 Pre-Check

Lists essential checks for temperature, humidity, sunlight, dust, and safety before system startup.

8.2 Starting the System

Outlines the step-by-step procedure for powering up and starting the system.

8.4 Numbering Extensions and C.O. Lines

Adding Cards to the System

10.1 Adding Stations and Trunks