Entris
®
BCE Operating Instructions 3
Contents
1 About these Instructions............................ 5
1.1 Scope......................................... 5
1.2 Other Applicable Documents ..................... 5
1.3 Target Groups.................................. 5
1.4 Symbols Used .................................. 5
1.4.1 Warnings in Operating Instructions ......... 5
1.4.2 Other Symbols........................... 5
2 Safety Instructions ................................. 6
2.1 Intended Use................................... 6
2.2 Personnel Qualification.......................... 6
2.3 Significance of these Instructions ................. 6
2.4 Proper Working Order of the Device ............... 6
2.5 Symbols on the Device .......................... 6
2.6 Electrical Equipment ............................ 7
2.6.1 Damage to the Electrical Equipment
of the Device............................ 7
2.6.2 Working on the Device’s Electrical
Equipment.............................. 7
2.6.3 Power Supply Unit and Power Supply Cable..7
2.7 Conduct in an Emergency........................ 7
2.8 Accessories and Spare Parts ...................... 7
2.9 Personal Protective Equipment ................... 7
3 Device Description ................................. 8
3.1 Device Overview................................ 8
3.2 Device Connections ............................. 8
3.3 Conformity-Assessed Devices ..................... 8
3.4 Symbols on the Device .......................... 8
4 Operating Concept................................. 9
4.1 Operating Display in Weighing Mode .............. 9
4.2 Menu and System Settings Display ................ 9
4.2.1 Buttons ...............................10
4.3 Displays in the Operating Display.................11
4.4 Menu Structure ...............................12
4.4.1 “Main Menu” Menu Structure.............12
4.4.2 “Toggle Between Weight Units”
Menu Structure ........................14
4.5 Navigating the Menus..........................14
5 Installation.......................................14
5.1 Scope of Delivery ..............................14
5.2 Selecting an Installation Site ....................14
5.3 Unpacking....................................15
5.4 Removing the Transport Lock ...................15
5.5 Assembling the Device..........................15
5.6 Acclimatizing the Device........................15
6 Getting Started...................................16
6.1 Installing the Power Supply Unit .................16
6.1.1 Assembling the Power Supply Unit ........16
6.1.2 Dismantling the Power Plug Adapter....... 16
6.2 Connecting the Power Supply ...................16
7 System Settings...................................16
7.1 Performing System Settings .....................16
7.2 Setting the Calibration and Adjustment ...........17
7.2.1 Switching the isoCAL Function On or
Off (Only Model i-1x)....................17
7.2.2 Setting Internal Calibration and
Adjustment (Only Model i-1x).............17
7.2.3 Setting the External Calibration and
Adjustment ............................17
7.3 Parameter List ................................18
7.3.1 “SETUP”/”BALANCE” Menu................18
7.3.2 “SETUP”/”GEN.SERV.” Menu...............19
7.3.3 “DEVICE”/”RS232” Menu .................20
7.3.4 “DEVICE”/”USB” Menu ...................20
7.3.5 “DEVICE”/”EXTRAS” Menu ................21
7.3.6 “DATA.OUT.”/”COM. SBI” Menu ............22
7.3.7 “DATA.OUT.”/”PRNT.PAR.” Menu ...........22
7.3.8 “DATA.OUT.”/”PC.DIREC.” Menu............23
7.3.9 “APPLIC.”/”WEIGH” Menu ................23
7.3.10 “APPLIC.”/”COUNT” Menu ................23
7.3.11 “APPLIC.”/”PERCENT” Menu...............24
7.3.12 “APPLIC.”/”NET.TOT.” Menu ...............24
7.3.13 “APPLIC.”/”TOTAL” Menu .................24
7.3.14 “APPLIC.”/”ANIM.WG” Menu ..............24
7.3.15 “APPLIC.”/”CALC.” Menu..................24
7.3.16 “APPLIC.”/”DENSITY” Menu ...............25
7.3.17 “APPLIC.”/”STATIST.” Menu ...............25
7.3.18 “APPLIC.”/”PEAK.HLD.” Menu..............25
7.3.19 “APPLIC.”/”CHECK.WG.” Menu.............25
7.3.20 “INPUT” Menu..........................26
7.3.21 “INFO” Menu ...........................26
7.3.22 “LANGUAG.” Menu ......................27
8 Operation ........................................27
8.1 Switching the Device On and Off.................27
8.2 Waiting for the Warm-up Time ..................27
8.3 Leveling the Device with a Level Indicator . . . . . . . . . 27
8.4 Overview of Calibration and Adjustment ..........27
8.5 Calibrating and Adjusting Device with
isoCAL Function (Only Model i-1x) ...............27
8.6 Calibrating and Adjusting the Device Internally
(Only Model i-1x)..............................28
8.7 Externally Calibrating and Adjusting the Device ....28
8.8 Printing Results of the Calibration and Adjustment
Process ......................................28
8.9 Weighing.....................................29
8.10 Setting or Changing an Application ..............29
8.11 Running Applications (Examples).................29
8.11.1 Executing the “Toggle Between
Weight Units” Function ..................29
8.11.2 Selecting Convertible Units and their
Decimal Places .........................29
8.11.3 Running the “Statistics” Application .......29
8.12 Printing Weighing Result with ID Marking .........30
To Next Page
Loading...
Need help?
General