Configuring Printouts
81
Configuring Printouts
Purpose
You can configure individual printout
formats for each application. Using the
total data record for Totalizing and
Net-total Formulation applications, you
can define which parameters are printed
using the c key.
In the “Print parameters” Setup menu,
single, component and total data
records can be configured, which
contain the available print items for the
respective applications. This should be
carried out after setting the applications
since some data in the printout is
application-dependent.
Characteristics
– Quantity and extent of printout lists:
6 lists each with a max. length of
30 print items
- Single printout Printer 1
- Component printout Printer 1
- Total data printout Printer 1
- Single printout Printer 2
- Component printout Printer 2
- Total data printout Printer 2
– Single, component and total data
records can be configured separately
– Print single printout: p key
Auto printout of application when
Setup menu is activated:
– Animal weighing (averaging)
– Checkweighing
– Classification
Signum
®
2 and 3 only:
– Print component printout:
Totalizing/Net-total formulation
with the O key (Setup: Application
3: Totalizing: Printout: Component
printout)
Signum
®
2 and 3 only:
– Print totalizing printout:
For selected application Totalizing/Net
total formulation with the c key
– When switching to another application
in Setup, only the application-
dependent printout lists are deleted.
The other printout lists remain saved.
– Print items can be deleted individually:
Press and hold the ( key
– Print items “Form Feed” for record
footer:
Move to the next label start for printer
type: YDP01IS: “Label” and YDP04IS,
setting “Label, manual form feed”
– ISO/GLP/GMP-compliant printout:
The Setup menu configuration under
“ISO/GMP-compliant printout” is also
active for configured printouts.
Preparation
§ Switch on the scale: Press the e key
§ While all segments are lit, press the
) key
§ Select Setup: Press the k key
repeatedly until setup is displayed
§ Select Config. printout: Press the
) key
§ Press the k key repeatedly until
prtprot is displayed
§ Press the ) key
prtprot
(see page 35 for a detailed menu list)
7
7.4 Header and ID header input
7.5 Quantity, interface
1
)
7.6 Standard, interface
1
)
7.7 Component, interface
1
)
7.8 Result, interface
1
)
7.9 Quantity, interface
2
)
7.10 Standard, interface
2
)
7.11 Component, interface
2
)
7.12 Result, interface
2
)
7.13 ISO/GMP
7.14 Date without time
1
)
7.15 Automatic printout
after stability
7.16 Flex print
7.17 Decimal separator
9
9.1 Factory settings
= Signum
®
2 and 3 only
– The rows of the protocol list can be
called up and activated individually.
Example: see under Configuration,
menu item 7.6
– The print selection set as active appears
with the left selection bar on the
display, e.g. gross, tare, net.
§ Extend printout, press the ) key, the
selection bar now appears on the right
of the display.
§ Select print items using the k key
§ Apply the desired print items by
pressing the ) key
§ Press the ( key to change the print
selection set as active.
The selection bar appears on the left.
The required print item is set as active
and appears in the printout.
1
) Only available if the time module is present.
– Print items can be deleted individually
from the active printout selection:
Press and hold the ( key
§ Save the settings with the ) key and
exit Setup: Press the ( key several
times.
Additional Functions
Printing the “Selection”and “List”
Settings
– LIST: Print the currently selected list
SELECT: Print currently selectable items
§ When selection bar is in LIST or
SELECT:
Press the p key
> Printout (example)
INDIV.PRT
List
====================
Net (N)
Gross (G#)
Tare
Tare (T2/PT2)
Piece count
====================
etc.
To Next Page
Loading...
