What to do if the SEI Industries Control Unit has no power?
If the SEI Industries Control Unit has no power, it might be due to a tripped circuit breaker. Try resetting the circuit breaker. Another possible cause is an issue with the aircraft or longline wiring, so you should check that wiring.
Why does the circuit breaker trip on my SEI Industries Control Unit?
If the circuit breaker trips on your SEI Industries Control Unit, the cause could be related to the aircraft or longline wiring. Inspect the wiring. Alternatively, there could be a mechanical jamb, in which case you should clear the jamb and check the linkage. The valve might be adjusted too high or too low; adjust the valve accordingly.
What to do if SEI Industries Control Unit pump won't run?
If the pump won't run, it could be due to a tripped circuit breaker. In this case, reset the circuit breaker. Another cause may be a disconnected cable, so check all cable connections. Finally, the power supply might be incompatible; compare the power supply output with the pump requirements.
What to do if my SEI Industries Control Unit valve leaks?
If the valve leaks, it could be due to damaged seals, so replace the seals. Another possible cause is that the valve is adjusted too high, so adjust the valve down.
Why are the fill times excessive for my SEI Industries Control Unit?
Excessive fill times may be due to a clogged debris filter, so clean the debris filter. A worn or damaged pump impeller can also cause this, so repair or replace the pump impeller. Check for excessive voltage drop in the longline and use larger gauge cables if needed. Also, inspect for damage to the cables and repair or replace them as necessary.
What to do if SEI Industries Control Unit valve closed won't open?
If the valve closed won't open, the motor protector might have activated. Power cycle to reset, and adjust the valve up. Another cause could be no open signal; check the aircraft or longline wiring. A damaged drive cable may also be the reason, so replace the drive cable.
What to do if SEI Industries Control Unit valve open won't close?
If the valve open won't close, the motor protector may have activated. Power cycle to reset it and adjust the valve down. A damaged drive cable could also be the problem, so replace the drive cable.
What to do if the SEI Industries Control Unit pump is noisy?
If the pump is noisy, it could be that the pump impeller is worn or damaged, so repair or replace it. Another possibility is debris in the impeller housing, so remove the debris.
Why does the SEI Industries Control Unit circuit breaker trip?
If the circuit breaker trips, it may be because debris is jamming the pump, so remove the debris. Another reason could be a damaged motor, so replace the motor.
Introduces the Bambi MAX and its capabilities, including models and accessories.
Covers attaching to cargo hook, power connection, and using longlines for safe operation.
Explains the IDS mechanism for automatic bucket mouth expansion and its function.
Procedure to measure and ensure safe overall length to avoid tail rotor strike.
Details the PowerFill Snorkel system for rapid bucket filling from various water sources.
Discusses Bambi MAX's design for foam use and the Sacksafoam dispensing system.
Details common valve issues, possible causes, and corrective actions.
Outlines weekly inspection procedures for the Bambi MAX and PowerFill system.
Importance and procedure for lubricating the pump output shaft seals for longevity.
Comprehensive guide for repairing and replacing the Bambi MAX valve components.
Recommendations for replacing valve seals, whether valve is in or out of shell.
Guide for replacing the drive cable for the Bambi MAX valve system.
Instructions for repairing damage to the Bambi MAX bucket shell using various methods.
Procedures for replacing the IDS hub assembly and its spokes.
Charts detailing capacity and weight for various Bambi MAX models.
Exploded view and parts list for the valve's shell assembly.
Diagram and parts for the valve's actuator and control unit.
Diagram and parts for the shell of models 1518-1821.
Diagram and parts list for rigging of models 1518-1821.
Illustrates the components of the PowerFill Snorkel system.
Details the warranty terms and conditions for Bambi MAX systems.
Wiring diagram for pilot controls.
Wiring diagram for the PowerFill pump system.
General| Brand | SEI Industries |
|---|---|
| Model | BAMBI MAX |
| Category | Control Unit |
| Language | English |
To Next Page
