Selco M4200 - Block Function 1; Block Function 2; Alarm 1 (Output Relay 1)

M4200 - User manual
Revision: 07.03.2017 Page 29
Parameter
Command
Description
Block function 1
WRITE ALM1 BLOCK1 OFF
Blocking alarm input 1 is not possible (by block function 1)
WRITE ALM2 BLOCK1 OFF
Blocking alarm input 2 is not possible (by block function 1)
WRITE ALM3 BLOCK1 OFF
Blocking alarm input 3 is not possible (by block function 1)
WRITE ALM4 BLOCK1 OFF
Blocking alarm input 4 is not possible (by block function 1)
WRITE ALM5 BLOCK1 OFF
Blocking alarm input 5 is not possible (by block function 1)
WRITE ALM6 BLOCK1 OFF
Blocking alarm input 6 is not possible (by block function 1)
WRITE ALM7 BLOCK1 OFF
Blocking alarm input 7 is not possible (by block function 1)
WRITE ALM8 BLOCK1 OFF
Blocking alarm input 8 is not possible (by block function 1)
WRITE ALM1 BLOCK1 ON
Blocking alarm input 1 is possible via external button (terminal 13)
WRITE ALM2 BLOCK1 ON
Blocking alarm input 2 is possible via external button (terminal 13)
WRITE ALM3 BLOCK1 ON
Blocking alarm input 3 is possible via external button (terminal 13)
WRITE ALM4 BLOCK1 ON
Blocking alarm input 4 is possible via external button (terminal 13)
WRITE ALM5 BLOCK1 ON
Blocking alarm input 5 is possible via external button (terminal 13)
WRITE ALM6 BLOCK1 ON
Blocking alarm input 6 is possible via external button (terminal 13)
WRITE ALM7 BLOCK1 ON
Blocking alarm input 7 is possible via external button (terminal 13)
WRITE ALM8 BLOCK1 ON
Blocking alarm input 8 is possible via external button (terminal 13)
Block function 2
WRITE ALM1 BLOCK2 OFF
Blocking alarm input 1 is not possible (by block function 2)
WRITE ALM2 BLOCK2 OFF
Blocking alarm input 2 is not possible (by block function 2)
WRITE ALM3 BLOCK2 OFF
Blocking alarm input 3 is not possible (by block function 2)
WRITE ALM4 BLOCK2 OFF
Blocking alarm input 4 is not possible (by block function 2)
WRITE ALM5 BLOCK2 OFF
Blocking alarm input 5 is not possible (by block function 2)
WRITE ALM6 BLOCK2 OFF
Blocking alarm input 6 is not possible (by block function 2)
WRITE ALM7 BLOCK2 OFF
Blocking alarm input 7 is not possible (by block function 2)
WRITE ALM8 BLOCK2 OFF
Blocking alarm input 8 is not possible (by block function 2)
WRITE ALM1 BLOCK2 ON
Blocking alarm input 1 is possible via external button (terminal 14)
WRITE ALM2 BLOCK2 ON
Blocking alarm input 2 is possible via external button (terminal 14)
WRITE ALM3 BLOCK2 ON
Blocking alarm input 3 is possible via external button (terminal 14)
WRITE ALM4 BLOCK2 ON
Blocking alarm input 4 is possible via external button (terminal 14)
WRITE ALM5 BLOCK2 ON
Blocking alarm input 5 is possible via external button (terminal 14)
WRITE ALM6 BLOCK2 ON
Blocking alarm input 6 is possible via external button (terminal 14)
WRITE ALM7 BLOCK2 ON
Blocking alarm input 7 is possible via external button (terminal 14)
WRITE ALM8 BLOCK2 ON
Blocking alarm input 8 is possible via external button (terminal 14)
Alarm 1 (output relay 1)
WRITE ALM1 RELAY1 ON
Alarm 1 (output relay 1) is active when alarm on input 1 is ON
WRITE ALM2 RELAY1 ON
Alarm 1 (output relay 1) is active when alarm on input 2 is ON
WRITE ALM3 RELAY1 ON
Alarm 1 (output relay 1) is active when alarm on input 3 is ON
WRITE ALM4 RELAY1 ON
Alarm 1 (output relay 1) is active when alarm on input 4 is ON
WRITE ALM5 RELAY1 ON
Alarm 1 (output relay 1) is active when alarm on input 5 is ON
WRITE ALM6 RELAY1 ON
Alarm 1 (output relay 1) is active when alarm on input 6 is ON
WRITE ALM7 RELAY1 ON
Alarm 1 (output relay 1) is active when alarm on input 7 is ON
WRITE ALM8 RELAY1 ON
Alarm 1 (output relay 1) is active when alarm on input 8 is ON
WRITE ALM1 RELAY1 OFF
Alarm 1 (output relay 1) is NOT active when alarm on input 1 is ON
WRITE ALM2 RELAY1 OFF
Alarm 1 (output relay 1) is NOT active when alarm on input 2 is ON
WRITE ALM3 RELAY1 OFF
Alarm 1 (output relay 1) is NOT active when alarm on input 3 is ON
WRITE ALM4 RELAY1 OFF
Alarm 1 (output relay 1) is NOT active when alarm on input 4 is ON
WRITE ALM5 RELAY1 OFF
Alarm 1 (output relay 1) is NOT active when alarm on input 5 is ON
WRITE ALM6 RELAY1 OFF
Alarm 1 (output relay 1) is NOT active when alarm on input 6 is ON
WRITE ALM7 RELAY1 OFF
Alarm 1 (output relay 1) is NOT active when alarm on input 7 is ON
WRITE ALM8 RELAY1 OFF
Alarm 1 (output relay 1) is NOT active when alarm on input 8 is ON