Sharp MX-M264N Installation Manual

MX-M264U IC card reader 24 – 4
F. System setting modification
IC card reader device registration
1) Device registration
a) Enter the card reader setting menu as shown below.
System Settings→Administrator Login→User Control→
Card Setting→Card Reader Device Registration
b) Press [Read] button.
c) Disconnect the connector which links the machine and the
IC card reader, and then insert it back.
d) Press [OK] button.
e) Check to confirm that values are displayed on "Product
ID" and "Vender ID".
f) Press [OK] button, and check to confirm that the success
dialog message is displayed.
2) Setting
a) Enter the card reader setting menu as shown below.
System Settings→Administrator Login→User Control→
Card Type/Card Reade Setting
b) Check-mark "Use IC Card for Authentication".
c) Press [OK] button.
G. IC card recognition check
MEMO: There are two check methods of IC card recognition. Use
either one to check that the IC card reader is recognized.
Check method 1
1) Enter the card reader setting menu as shown below.
System Settings→USB-Device Check
2) Check to confirm that "Card Reader/Writer" is displayed.
Check method 2
Check to confirm that the icon of the card reader is displayed on the
system area of the home screen.
(If there is no check-mark on "Use IC Card for Authentication," the
icon is not displayed.)
H. External fixture attachment
NOTE: Before installation, be sure to turn both the operation and
main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
1) Attach the operation panel base plate.
2) Attach the front cabinet upper.
I. Making and importing of the setting file for HID
card reading
NOTE: The following procedures are executed only when a
request is made by a user for customizing the data format
of IC card reading.
1) Make the setting file for HID card reading.
For the making procedures, refer to the Manual of Setting File
for HID Card Reading.
2) Copy the setting file to a USB memory.
3) Import the setting file for HID card reading to the machine.
a) Connect the USB memory to the USB connector in the
operation section.
b) System Settings→Administrator Login→User Control→
Card Area Setting→Importing from the Set Up File
c) Select the file made in procedure 1) above.
d) Press [Back] button.
(The setting file for HID card reading is loaded.)
4) Perform the operation check.
a) System Settings→Administrator Login→User Control→
Card Area Setting→Card Scan Test
b) While holding the IC card over the IC card reader, press
[Execute] button of “Card Scan Test”.
c) The IC card data are loaded. The test result is displayed
as shown below:
Display when loading is successfully completed:
Display when loading is failed:
When an error occurs, troubleshoot the cause and remove the trou-
ble. Then perform the above procedures again.
Possible causes for an error may be error of the IC card or
improper contents of the setting file for HID card reading.
2
2
1
2
2
Detail of error
Error display Error content and remedy
Card is not
found.
Content The card is not detected.
Remedy Check to confirm that the card is securely
inserted into the IC card reader.
Read Error. Content A read error occurs.
Remedy Check to confirm that the card and the card
reader operate normally with a personal
computer, etc.
Read Success.
Card ID : XXXXX
Facility Code : XXXXX

Sharp MX-M264N Specifications

General

Print Technology	Laser
Functions	Print, Copy, Scan, Fax
Print Speed	26 ppm
Max Print Resolution	600 x 600 dpi
Standard Paper Capacity	1100 sheets
Max Paper Capacity	2100 sheets
Automatic Duplexing	Yes
ADF Capacity	100 sheets
Scan Resolution	600 x 600 dpi
Copy Speed	26 cpm
Copy Resolution	600 x 600 dpi
Connectivity	Ethernet, USB