MX-M264U SIMULATION 6 – 23
25-2
Purpose
Setting
Function (Purpose)
Used to make the initial setting of toner
density when replacing developer. (Auto-
matic adjustment)
Section
Image process (Photoconductor/Develop-
ing)
Operation/Procedure
1) Press [EXECUTE] key.
The developing motor rotates and the toner density sensor makes
sampling of the toner density, displaying the detected level.
After stopping the developing motor, it is set as the reference toner
density control level.
CAUTION: When the above operation is interrupted on the way, the
reference toner concentration level is not set. Also when
error code of EE-EL or EE-EU is displayed, the refer-
ence toner density level is not set normally.
CAUTION: Do not execute this simulation except when new devel-
oper is supplied. If it is executed in other cases, under-
toner or overtone may occur, causing a trouble.
Display during execution of the simulation
Error content
25-4
Purpose
Adjustment/Setting/Operation data check
Function (Purpose)
Used to display the operation data of the
toner correction quantity. (Not used in the
market.)
Section
Process
Operation/Procedure
The operation data of the toner supply quantity are displayed.
26
26-1
Purpose
Setting
Function (Purpose)
Used to set Yes/No of installation of the Job
separator.
Section
Paper exit
Operation/Procedure
1) Enter the set value with 10-key.
2) Press [OK] key. (The set value is saved.)
This setting is required to use the Job separator.
26-2
Purpose
Setting
Function (Purpose)
Used to set the paper size of the paper feed
tray. (When the paper size is changed, this
simulation must be executed to change the
paper size in software.)
Section
Paper feed
Operation/Procedure
Select a paper size and a weight system to be changed.
Item/Display Content
Display
range
Default
value
AT DEVE ADJ Automatic development
adjustment value
1 - 255 128
Item/Display Content
TCS Toner sensor output value
Display Error name Error content
EE-EL EL abnormality The sensor output level is less than 78.
EE-EU EU abnormality The sensor output level exceeds 178.
Item/Display Content
Display
range
TONER DEN_LT Current toner density sensor output
value (final value)
1 - 255
TONER DEN_ST Current toner density reference
value display (the value including all
the correction values)
1 - 255
AUTO DEVE Automatic development adjustment
value
1 - 255
ALL All correction reference value 1 - 255
LIFE Life correction value -128 - 127
ENV Environment correction value -128 - 127
DUPLEX Duplex correction value -128 - 127
PRINT RATE Print ratio correction value -128 - 127
AREA Area correction value -128 - 127
AUTO DEVE AREA Area in the auto development
adjustment
-128 - 127
CURRENT AREA Current area -128 - 127
Item/Display Content
A 0 YES Job separator provided
1 NO Job separator not provided
Item Setting value Content
LEGAL SET 0 8.5 x 14
1 8.5 x 13.4
2 8.5 x 13.5
G/LBS SET 0 GRAM
1LBS
Destination
Setting value
LEGAL SET G/LBS SET
U.S.A 8.5 x 14 LBS
CANADA 8.5 x 14 LBS
INCH 8.5 x 14 LBS
JAPAN 8.5 x 14 GRAM
AB_B 8.5 x 14 GRAM
EUROPE 8.5 x 14 GRAM
U.K. 8.5 x 14 GRAM
AUS. 8.5 x 14 GRAM
AB_A 8.5 x 14 GRAM
CHINA 8.5 x 14 GRAM
To Next Page
Loading...
