MX-M264U SIMULATION 6 – 24
26-3
Purpose
Setting
Function (Purpose)
Used to set the specifications of the auditor.
(Setting must be made according to the
auditor use conditions.)
Section
Auditor
Operation/Procedure
Select an item to be set with the touch panel.
(*1) Displayed only when EQUITRAC.
(*2) Details of the vendor mode
Details of the vendor mode
Operation 1:
Standby during setting time of auto clear. Default is 60 seconds,
which can be changed in the system setting.
Operation 2:
Auto clear is not made.
Operation 3:
The display is shifted to the initial screen.
26-5
Purpose
Setting
Function (Purpose)
Used to set the count mode of the total
counter and the maintenance counter. (A3/
11x17 size)
Section
Operation/Procedure
1) Select an item to be set with scroll keys.
2) Enter the setting value with 10-key
1 = Count up by 1, 2 = Count up by 2
3) Press [OK] key.
The set value in step 2) is saved.
Item/Display Content
Default
value
BUILT-IN
AUDITOR
P10 Built-in auditor mode
(standard mode) operation.
P10
OUTSIDE
AUDITOR
NONE No external connection
vendor is used.
NONE
P VENDOR1 Coin vendor mode
(Only the copy mode can
be controlled.)
P VENDOR3 Vendor mode in which
signals for the intercard
connected to the PCU are
used for communication in
parallel I/F.
P OTHER Mode for an external
auditor connected to the
SCU.
VENDOR-EX
(*1)
Vendor I/F for EQUITRAC
VENDOR-EX
(MULTI) (*1)
VENDOR-EX + Multi job
cueing Enable mode
S_VENDOR Serial vendor mode
DOC ADJ ON Support for the auditor in
document filing print
OFF
OFF No support for the auditor in
document filing print
PF ADJ ON Continuous printing is
performed in the duplex
print mode.
If the remaining money
expires during continuous
printing, the sheets in the
machine are discharged
without being printed on the
back surfaces.
OFF
OFF Continuous printing is not
performed in the duplex
print mode. (The remaining
amount is checked for
printing every surface in all
the printing process.)
If the remaining money
expires during printing, the
sheet is discharged without
printing on the back
surface.
VENDOR
MODE (*2)
MODE1 Vendor mode 1 MODE
3
MODE2 Vendor mode 2
MODE3 Vendor mode 3
COUNTUP
TIMING
FUSER_IN Mode in which the detection
timing of the paper lead
edge by the sensor after the
paper passes the fusing
section is used as the
money charging timing.
EXIT_
OUT
FUSER_OUT Mode in which the detection
timing of the paper rear
edge by the sensor after the
paper passes the fusing
section is used as the
money charging timing.
EXIT_OUT Mode in which the detection
timing of the paper rear
edge by the paper exit
sensor of the right paper
exit tray or of the after
process unit is used as the
money charging timing.
Completion
of the
specified
quantity.
(Money
remaining)
Insufficient money during
copy job
Completion
of the
specified
quantity.
(No money
remaining)
BW
(no money
remaining)
BW
(money
remaining)
Condition 1 Condition 2 Condition 3 Condition 4
MODE1 Operation 1 Operation 2 Operation 2 Operation 1
MODE2 Operation 1 Operation 1 Operation 2 Operation 1
MODE3 Operation 1 Operation 3 Operation 2 Operation 3
Item/Display Content Default value
A TOTAL (B/W) Total counter (B/W) 1
(Japan)
2
(Except Japan)
B MAINTE (B/W) Maintenance counter (B/W) 2
C DEV (B/W) Developer counter (B/W)
Item/Display Content
Default
value
To Next Page
Loading...
