MX-M700N SIMULATION 7 – 12
5-2
Purpose
Operation test/Check
Function (Purpose)
Used to check the operation of the heater
lamp and the control circuit.
Section
Fusing/Paper exit
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press [START] key.
The load selected in procedure 1 performs ON/OFF operation.
Press [SYSTEM SETTINGS] key to stop the operation of the
load.
The ON/OFF operation of the selected heater lamp is repeated
every 500ms five times.
5-3
Purpose
Operation test/Check
Function (Purpose)
Used to check the operation of the scanner
lamp and the control circuit.
Section
Optical (Image scanning)
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press [START] key.
The load selected in procedure 1 turns ON for 10sec.
The operation can be stopped with the [SYSTEM SETTINGS]
key.
NOTE: CIS: only when the DSPF is installed.
5-4
Purpose
Operation test/Check
Function (Purpose)
Used to check the operation of the dis-
charge lamp and the related circuit.
Section
Process
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press [START] key.
The load selected in procedure 1 turns ON for 30sec.
The operation can be stopped with the [SYSTEM SETTINGS]
key.
6
6-1
Purpose
Operation test/Check
Function (Purpose)
Used to check the operation of the paper
transport system loads (clutch, solenoid)
and the control circuit.
Section
Paper transport (Discharge/Switchback/
Transport)
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press the [START] key.
The load selected in procedure 1 is operated.
The operation can be stopped with the [SYSTEM SETTINGS]
key.
1 HL1 (LOWER) Heater lamp 1 (Lower)
2 HL2 (UPPER) Heater lamp 2 (Upper)
3 HL3 (LEFT) Heater lamp 3 (Left)
SIMULATION 5-2
HEATER LAMP TEST. SELECT 1-3 ,AND PRESS START.
1.HL1(LOWER)
2.HL2(UPPER)
3.HL3(LEFT)
2
SIMULATION 5-3
COPY LAMP TEST. SELECT 1-2, AND PRESS START.
1.COPY LAMP
2.CIS
1
SIMULATION 5-4
DISCHARGE LAMP CHECK. SELECT 1, AND PRESS START.
1.DL
1
1 MSWPR MSW reset signal
2 HLPR Heater power relay signal
3 DCPR DC power relay signal
4 MM Main motor
5 DM Drum motor
6 DVM Developing motor
7 TURM Transfer separation motor
8 TRM PS front motor
9 POM1 Paper exit motor 1
10 POM2_FW Paper exit motor 2 forward rotation
11 POM2_RV Paper exit motor 2 reverse rotation
12 VPM Paper transport motor
13 RRC Resist roller clutch signal
14 PSBC Brake clutch signal
15 PSPS Separation pawl
16 T1PFC Tray 1 paper feed clutch
17 T2PFC Tray 2 paper feed clutch
18 HPFC Horizontal transport clutch
19 T1PUS Tray 1 pickup solenoid
20 T2PUS Tray 2 pickup solenoid
21 HPLS Relay path clock solenoid
22 T1LUM Tray 1 lift-up motor
23 T2LUM Tray 2 lift-up motor
24 DSKPFC1 Desk paper transport clutch upstream side
25 DSKPFC2 Desk paper transport clutch downstream side
26 M1PFC Tray 3 paper feed clutch
27 M2PFC Tray 4 paper feed clutch
28 M1PUS Tray 3 pickup solenoid
29 M2PUS Tray 4 pickup solenoid
30 M1LUM Tray 3 lift-up motor
31 M2LUM Tray 4 lift-up motor
32 TRC_LCC Desk clutch sync signal
33 FUM Fusing motor
34 MPFPUS Manual pickup solenoid
35 MPFC Manual paper feed clutch signal
36 MPFGS Manual paper feed gate solenoid
37 WEBM Fusing web feed motor
SIMULATION 6-1
FEED OUTPUT CHECK. SELECT 1- 37, AND PRESS START.
1.MSWPR 2.HLPR 3.DCPR 4.MM 5.DM
6.DVM 7.TURM 8.TRM 9.POM1
10.POM2_FW 11.POM2_RV 12.VPM
13.RRC 14.PSBC 15.PSPS 16.T1PFC
17.T2PFC 18.HPFC 19.T1PUS 20.T2PUS
21.HPLS 22.T1LUM 23.T2LUM 24.DSKPFC1
25.DSKPFC2 26.M1PFC 27.M2PFC 28.M1PUS
29.M2PUS 30.M1LUM 31.M2LUM 32.TRC_LCC
33.FUM 34.MPFPUS 35.MPFC 36.MPFGS
37.WEBM
2
To Next Page
Loading...
