What to do if my Shott BP-85HS-A is running and error message EE 3 is displayed?
If your Shott Heat Pump displays error message EE 3 while running, the compressor temperature sensor may be incorrectly connected or defective. Check the sensor resistance value and replace if necessary. You can also replace the control board.
What to do if my Shott BP-85HS-A Heat Pump does not work and error message EE 2 is displayed?
If your Shott Heat Pump displays error message EE 2 and isn't working, the ambient temperature sensor may be incorrectly connected or defective. Check the sensor resistance value and replace it if necessary. You can also replace the control board.
What to do if my Shott BP-85HS-A does not work and error message EE 1 is displayed?
If your Shott Heat Pump displays error message EE 1 and isn't working, the pool temperature sensor may be incorrectly connected or defective. Check the sensor resistance value and replace it if necessary. You can also replace the control board.
What to do if my Shott Heat Pump does not start?
If your Shott Heat Pump doesn't start, first ensure that the 3 minutes required for pump start have elapsed. If the pool temperature is at or above the set temperature, the pump will only start when the pool temperature drops below the set temperature. Finally, confirm that the pump operating mode is set to the required mode.
Why is my Shott Heat Pump not working and error message EE 6 is displayed?
If your Shott Heat Pump displays error message EE 6 and isn't working, it could be due to several reasons. The compressor temperature might be too high, so wait until it drops. There could be a refrigerant circuit leak, so check for leaks and replace any defective parts. Alternatively, the capillary circuit might be clogged, in which case it should be replaced.
What to do if my Shott Heat Pump is running but the water is not heating?
If your Shott Heat Pump is running but not heating the water, first ensure that air exits the front part of the heat pump. If the heat pump was just installed, allow 24 to 48 hours to reach the set temperature. If the pool water has significantly cooled since the last use, it may take 24 to 36 hours to reach the desired temperature.
What does it mean if my Shott Heat Pump displays error message EE 8 and doesn't work?
If your Shott Heat Pump displays error message EE 8 and does not work, it indicates that the control board wiring is defective. Check the wiring.
What does it mean if my Shott Heat Pump displays error message EE 4?
If your Shott Heat Pump is running and displays error message EE 4, it means the automatic defrost did not run correctly. Increase the water flow at the pump inlet.
What does it mean if my Shott BP-85HS-A displays error message EE d?
If your Shott Heat Pump displays error message EE d, it means there are functional parameter changes and parameter 9 is not set to 1. Set the correct parameter values to 1.
What does it mean if my Shott BP-85HS-A displays error message EE 3?
If your Shott Heat Pump is running and displays error message EE 3, it indicates that the compressor temperature sensor is incorrectly connected or defective. Check the sensor resistance value and replace it if necessary.
Declaration of conformity to EU directives and standards for heat pumps.
Covers general, special, and restricted conditions of the product warranty.
Crucial safety guidelines for using heated pools, including temperature limits.
Recommendations for optimizing energy consumption and savings for the heat pump.
Overview of the product scope, composition, and definitions.
Steps for inspecting, handling, and positioning the heat pump correctly.
Guidelines for necessary clearance, noise reduction, and proper disposal.
Instructions for connecting water circuits, including warnings and layout.
Essential steps for making safe and correct electrical connections to the heat pump.
Procedures for installing mains sockets and replacing the power cord.
Final checks and precautions before initial start-up and commissioning.
Guide to using the control panel: turning on/off, standby, starting, and mode selection.
Steps for starting the heat pump and regulating temperature.
Configuration of automatic start and standby modes for convenience.
Using manual defrost, key lock, and displaying sensor temperatures.
Accessing and modifying advanced functional parameters for heat pump operation.
Specific settings for pool temperature, defrost start, and stop temperatures.
Details on defrost repetition time, duration, and compressor protection temperature.
Settings for automatic restart, operating mode, and temperature deviation.
Selecting control modes and using the pressure manometer.
Information on ambient, pool temperature, and flow sensors.
Details on compressor, heat exchanger, and pressure sensors for safety.
Function and trigger pressure of the low pressure sensor.
Tables of resistance values for temperature sensors.
Tables of resistance values for the compressor temperature sensor.
User checks, technician controls, winter protection, and spring commissioning.
Guide to solving common heat pump issues and error messages.
Special notes for replacing specific parts like manometer, sensors, filter, and capillary.
Procedure for checking and addressing frost on the radiator.
To Next Page
General
