SICK DUSTHUNTER SB30

To Next Page

MMM

MMMOPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

DUSTHUNTER SB30

Dust Measuring Device

Title Page

Main Page

Table of Contents3
Important Information6
Main Hazards6
Hazard through Hot And/Or Aggressive Gases and High Pressure6
Hazards through Electrical Equipment6
Hazards through Laser Beam6
Symbols and Document Conventions7
Warning Symbols7
Warning Levels and Signal Words7
Information Symbols7
Intended Use7
Responsibility of User8
General Information8
Safety Information and Protective Measures8
Product Description10
Measuring Principle, Measured Variables10
Functional Principle10
Response Time11
Function Check12
Device Components13
Sender/Receiver Unit15
Flange with Tube17
Optional External Purge Air Unit18
Voltage and Purge Air Supply18
Installation Accessories18
Test Equipment for Linearity Test19
SOPAS ET (PC Program)19
Assembly and Installation20
Project Planning20
Assembly22
Fitting the Flange with Tube22
Work to be Performed23
Fitting the Optional External Purge Air Unit23
Assembly Work24
Fitting the Weather Hood25
Fitting the Optional MCU Control Unit25
Electrical Installation26
Electrical Safety26
Properly Installed Power Isolating Switches26
Lines with Correct Rating26
Grounding the Devices26
Responsibility for System Safety26
General Information, Prerequisites27
Connecting the Optional MCU Control Unit27
Installing the Purge Air Supply27
Optional External Purge Air Unit27
Installing the Non-Return Valve Option29
Connecting the Sender/Receiver Unit30
Work to be Done30
Connection of Connection Line30
Standard Connection (Without Options)31
Start-Up and Parameter Settings32
Fitting the Sender/Receiver Unit32
Adapting the Sender/Receiver Unit to the Duct Diameter32
Fitting and Connecting the Sender/Receiver Unit on the Duct35
Setting the Measuring System Parameters36
Factory Settings36
Changing Settings Using the Jumper on the Processor Board37
Setting Measuring Range and Limit Value37
Addressing38
Measuring Range Parameterization38
Manual Measuring Range Parameterization on the Device39
Automatic Measuring Range Parameterization Via SOPAS ET39
Installing SOPAS ET40
Password for SOPAS ET Menus40
Connection to the Device Via USB Line40
Finding the DUSTHUNTER COM Port40
Connection to the Device Via Ethernet (Option)41
Factory Settings43
Resetting Parameters44
Setting Modbus® Parameters45
Calibration for Dust Concentration Measurement46
Data Backup in SOPAS ET47
Starting Measurement Mode48
Setting the Ethernet Module Parameters49
Transport and Storage50
Transport50
Storage50
Maintenance51
General51
Maintenance on the Sender/Receiver Unit53
Maintenance on the Purge Air Supply54
Control Unit MCU with Integrated Purge Air Supply55
Replacing the Button Cell in the Control Unit56
Optional External Purge Air Unit57
Shutdown58
Troubleshooting59
General59
Sender/Receiver Unit60
Specifications61
Compliances61
Technical Data62
Dimensions, Part Numbers64
Sender/Receiver Unit64
Flange with Tube65
MCU Control Unit66
Optional External Purge Air Unit68
Weather Hoods69
Accessories70
Connections for Sender/Receiver Unit70
Line, Sender/Receiver Unit - MCU70
Purge Air Supply70
Assembly Parts70
Device Check Accessories70
Consumable Parts for 2-Years Operation70

Other manuals for SICK DUSTHUNTER SB30

Installation Operation & Maintenance72 pages

Need help?

Do you have a question about the SICK DUSTHUNTER SB30 and is the answer not in the manual?

SICK DUSTHUNTER SB30 Specifications

General

Brand	SICK
Model	DUSTHUNTER SB30
Category	Monitor
Language	English

Table of Contents

Other manuals for SICK DUSTHUNTER SB30

SICK DUSTHUNTER SB30 Specifications