Siemens SINUMERIK 808D ADVANCED Parameter Manual

20204 WAB_CLEARANCE_TOLERANCE C06 W1
mm Change of direction with SAR DOUBLE PowerOn
-
- - 0.01, 0.01, 0.01, 0.01,
0.01, 0.01, 0.01, 0.01...
0.0 - 1/1 M
Description: In the case of smooth approach and retraction, the point defined with DISCL, from
which, in the
case of infeed from the initial plane, traversing is carried out at lower
speed (G341) or the point in which the actual approach movement begins (G 340), must
lie between the initial plane and the approach plane.
If this point lies outside this interval and the deviation is less than or equal to
this machine data, it is assumed that the point lies in the approach or retraction
plane.
If the deviation is greater, then alarm 10741 is output.
Example:
An approach is made from position Z = 20. The SAR plane is at Z = 0. The point defined
by DISCL must therefore lie between these two values. If it lies between 20.000 and
20.010
or between
0 and -0.010, it is assumed that the value 20.0 or 0.0 was programmed
(under the condition that the MD has the value 0.010). The alarm is output if the
position is greater than 20.010 or less than -0.010.
20256 CUTCOM_INTERS_POLY_ENABLE C09 W1
- Intersection procedure for polynomials is possible BOOLEAN PowerOn
-
- - TRUE, TRUE, TRUE,
TRUE, TRUE, TRUE,
TRUE, TRUE...
0 - 1/1 M
Description: If this machine data is TRUE and tool radius compensation active, the transitions at
outer corners where polynomes (splines) are involved can be treated with the
intersection mode. If the machine data is FALSE, conic sections (circles) are always
inserted in this case.
If the machine data is FALSE, the response is identical to that of software releases
older than 4.0.
20262 SPLINE_FEED_PRECISION EXP, C09, C05 -
- Permissible rel. error of path velocity for spline DOUBLE PowerOn
-
808d-me42 - 0.001, 0.001, 0.001,
0.001, 0.001, 0.001,
0.001, 0.001...
0.000001 1.0 0/0 S
808d-me62 - 0.001, 0.001, 0.001,
0.001, 0.001, 0.001,
0.001, 0.001...
0.000001 1.0 0/0 S
808d-te42 - 0.001, 0.001, 0.001,
0.001, 0.001, 0.001,
0.001, 0.001...
0.000001 1.0 0/0 S
808d-te62 - 0.001, 0.001, 0.001,
0.001, 0.001, 0.001,
0.001, 0.001...
0.000001 1.0 0/0 S
808d-mte40 - 0.001, 0.001, 0.001,
0.001, 0.001, 0.001,
0.001, 0.001...
0.000001 1.0 7/2 M
808d-mte60 - 0.001, 0.001, 0.001,
0.001, 0.001, 0.001,
0.001, 0.001...
0.000001 1.0 7/2 M
Machine data
3.3 Channel-specific machine data
Parameter Manual
138 Parameter Manual, 08/2015, 6FC5397-8EP40-0BA1

Siemens SINUMERIK 808D ADVANCED Specifications

General

Brand	Siemens
Model	SINUMERIK 808D ADVANCED
Category	Control Unit
Language	English