Index
Job planning
Programming Manual, 03/2006 Edition, 6FC5398-2BP10-1BA0
Index-11
Sparking-out stroke, 11-2
SPATH, 5-22
Speed coupling, 13-15
Speed ratio, 13-18
SPF, 3-3
SPI, 13-1, 13-2, 13-21
SPIF1, 15-31
SPIF2, 15-31
Spindle motions, 10-54
Spindle Replacement
GET, 1-55
RELEASE, 1-55
SPLINE, 14-8, 14-11
Spline grouping, 5-11
Spline interpolation, 5-3, 5-24
A-Spline, 5-8
B spline, 5-8
C spline, 5-9
Compressor, 5-11
SPLINEPATH, 5-11
SPN, 12-5
SPOF, 12-2
SPOS, 13-20
SPP, 12-5
SQRT, 1-19
SR, 15-31
SRA, 15-31
ST, 15-31
STA, 15-32
START, 1-41
Start/stop axis, 10-46
STARTFIFO, 9-42
STAT, 7-69, 7-73
Statement list, 15-1
Station/position change, 13-44
Status of coupling, 9-36
Stock removal, 14-1
Stop, 13-38
Stop and retract
Extended, 13-30
STOPFIFO, 9-42
STOPRE, 5-25, 5-28, 5-29, 9-42, 11-3
STRING, 1-4
String length, 1-30
String operations, 1-26
STRING_ARRAY, 1-26
STRINGIS, 13-3
Basic information, 13-4
Detailed Information, 13-5
NC addresses, 13-5
Return values, 13-4
Scope of NC language, 13-4
Scope of testing, 13-3
Special checks, 13-3
STRINGVAR, 1-26
STRLEN, 1-30
Structuring statement for the Step editor, 3-24
Subroutine call
indirect, 1-14
Subroutine call with M/T function, 2-31
Subroutine call, search path, 3-5
Subroutine with path specification and parameters, 2-
24
Subroutines, 2-1
Indirect subroutine call, 2-21
Modal subroutine call, 2-19
Nesting, 2-3
Program repetition, 2-18
SAVE mechanism, 2-3
Subroutine call, 2-9
Subroutine with parameter transfer, 2-9
Subroutines with parameter transfer
Array definition, 2-8
Parameter transfer between main program and
subroutine, 2-8
SUBSTR, 1-32
SUPA, 6-21
Synchronism
coarse, 13-15
Fine, 13-15
Setpoint-based synchronism, 13-15
Synchronized action, 13-42
Synchronized action parameters, 10-15
Synchronized actions
ASUB, 10-80
Block search, 10-80
Boundary conditions for important events, 10-78
CANCEL, 10-81
End of program, 10-80
List of values with SET and REP, 10-59
Main run variable, 10-9
Mode change, 10-78
NC Stop, 10-79
Power on, 10-78
Preprocessing variables, 10-9
Repositioning, 10-81
Reset, 10-79
Synchronous oscillation
Assignment of oscillating and infeed axes, 11-9
Define infeeds, 11-9
Evaluation, interpolation cycle, 11-12
Infeed in reversal point range, 11-10
Infeed movement, 11-10
Next partial infeed, 11-12
Stop at the reversal point, 11-11
Synchronized actions, 11-9
Synchronous spindle, 13-12
Block change behavior, 13-19
To Next Page
Loading...
