Pos: 113 /100 Sig ma/100 BA Ze ntrifugen Sigma (St andardmo dule)/061 Betrieb_ Spincontrol Basic /Spincontr ol Basic /061-0 030-0030 Start en einer Zentrif ugation (auß er 2-7) @ 27\m od_14053203492 96_68.docx @ 193795 @ 3 @ 1
6.3.3 Starting a centrifugation run
The centrifuge is ready for operation when the mains power switch is on
and the lid is closed.
• Press the start/stop key in order to start a centrifugation run.
Pos: 114 /010 Uni versalmodul e/ Leerz eile @ 0\mod_12 02116244500 _0.docx @ 114 @ @ 1
Pos: 115 /100 Sig ma/100 BA Ze ntrifugen Sigma (St andardmo dule)/061 Betrieb_ Spincontrol Basic /Spincontr ol Basic /061-0 030-0040 Un terbrechen ei ner Zentrifugati on @ 27\mod_14 05320350701 _68.docx @ 1938 09 @ 3 @ 1
6.3.4 Interrupting a centrifugation run
• Press the start/stop key in order to interrupt a centrifugation run. The
centrifugation run will be terminated prematurely.
Pos: 116 /010 Uni versalmodule/ Leerzeile @ 0\mod_12 02116244500 _0.docx @ 114 @ @ 1
Pos: 117 /100 Sig ma/100 BA Ze ntrifugen Sigma (St andardmo dule)/061 Betrieb_ Spincontrol Basic /Spincontr ol Basic /06 1-0030-0050 Un terbrechen ei nes Bremsvorgangs @ 27\mod _1405320352 187_68.docx @ 19 3823 @ 3 @ 1
6.3.5 Interrupting a deceleration process
• Press the start/stop key during a deceleration process in order to
interrupt it and to restart the centrifuge.
Pos: 118 /010 Uni versalmodule/ Leerzeile @ 0\mod_12 02116244500 _0.docx @ 114 @ @ 1
Pos: 119 /100 Sig ma/110 BA Ze ntrifugen Sigma (Proj ekte)/1-1 4_1-14K/061 Betrieb/Spincontr ol Basic/061-0 030-0060 Dre hzahl / Relative Z entrifugalbesc hleunigung (RZ B) - nur 1-14 @ 28\mod_140 5320827081_6 8.docx @ 19 5559 @ 3 @ 1
6.3.6 Speed / Relative centrifugal force (RCF)
The RCF value is determined by the rotor geometry and speed. The RCF
and speed values, therefore, depend on each other. If one of the two
values is entered, the other value will be set automatically.
• To preselect a speed value or a RCF value, press the select key
repeatedly until the corresponding unit flashes on the display.
• Select the desired speed or RCF value via the arrow keys.
• Confirm the selection by pressing the start/stop key.
The data will also be accepted and saved after approx. 20 seconds if no
other key is pressed within this time period.
During operation, you can switch from the speed value to the RCF value
and vice versa via the arrow keys.
Pos: 120 /010 Uni versalmodule/ Leerzeile @ 0\mod_12 02116244500 _0.docx @ 114 @ @ 1
Pos: 121 /100 Sig ma/110 BA Ze ntrifugen Sigma (Proj ekte)/1-1 4_1-14K/061 Betrieb/Spincontr ol Basic/061-0 030-0060-001 0 Ändern des Dre hzahl-/RZ B-Wertes während des L aufs - nur 1- 14 @ 28\mod_14 05320827915 _68.docx @ 19 5573 @ 4 @ 1
6.3.6.1 Changing the speed/RCF value during centrifugation
The preselected speed or RCF value can be changed during centrifugation.
• Press the select key repeatedly until the desired unit flashes on the
display.
• Change the speed or RCF value by pressing the arrow keys. The
parameters will take effect immediately.
Pos: 122 /010 Uni versalmodule/ Seitenwechsel @ 0\mod_12 02116244312_0 .docx @ 105 @ @ 1
To Next Page
Loading...
