What to do if foot switch is actuated during power-on of Sirona Medical Equipment?
If the foot switch was accidentally activated during the power-on of your Sirona Medical Equipment, switch the unit on again, this time without pressing the foot switch.
Why is the tank illumination not working correctly on my Sirona Medical Equipment?
If the tank illumination is not working correctly on your Sirona Medical Equipment, it could be due to: * Fixed water supply being selected. * No tank being selected. Ensure tank illumination complies with the operating instructions. If the problem persists, there may be a unit issue.
Why isn't the boost function working on my Sirona Medical Equipment?
If the boost function isn't working on your Sirona Medical Equipment, check the following: * For power settings between 1-4%, no power boost is needed due to the endo function. * If the power is at 100%, no further power boost is possible. * The boost function may have been deactivated. Reactivate it by pressing keys 1 and 2 simultaneously.
What to do if the Sirona Medical Equipment tip is worn, loose, or incorrect?
If you're experiencing issues with the tip of your Sirona SIROPERIO 4 PS or SIROPERIO PE 8 equipment, consider the following: * For a worn tip, check its length with a tip gauge and replace it if necessary. * If the tip is loose, tighten it using the torque wrench. * If there is no tip, screw one on and tighten it with the torque wrench. * If you are using a tip other than the SIROPERIO 4 PS or SIROPERIO PE 8 tip, deactivate the detection function. * For a broken tip, screw on a new one and tighten it using the torque wrench. * Ensure the torque wrench is removed after tightening. * Verify the handpiece supply cable is correctly connected.
Why is there no display on my Sirona Medical Equipment?
If there is no display on your Sirona Medical Equipment, it could be due to several unit-related issues, such as a defective display cable, primary fuse, board pair, transformer, or display board.
What to do if the keyboard is not responding on my Sirona Medical Equipment?
If the keyboard on your Sirona Medical Equipment is not responding, consider these points: * If you're trying to save PERIO keys, make the desired settings and then press the PERIO key longer until the illumination starts flashing. * For setting intermediate power values, keep the power keys pressed longer. * If PERIO keys are not assigned, press the 1 key and switch the unit on again. If the problem persists, there may be an issue with the connecting cable, membrane keyboard, or display board.
How to fix no light on Sirona Medical Equipment?
If there is no light on your Sirona Medical Equipment, try the following: * If the start screen remains after removing the handpiece, ensure the unit is switched on without actuating the foot switch. * Check that the hose is properly plugged in and reconnect if necessary. If the issue persists, the foot switch might be defective (replace it), or there could be a microswitch issue in the holder.
Why is the handpiece power low on my Sirona Medical Equipment?
If you're experiencing low handpiece power with your Sirona Medical Equipment, consider these potential causes: * The tip might be worn. Check its length with a tip gauge and replace it if necessary. * The power setting might be set too low. Check and correct the power setting. * Only flushing might be activated on the foot switch. Actuate both foot pedals simultaneously. If these steps don't resolve the issue, the handpiece might be defective (replace it), the foot switch or hose might not be connected properly (check and reconnect them), or there might be a more complex unit issue.
General| Brand | Sirona |
|---|---|
| Model | PerioScan |
| Category | Dental equipment |
| Language | English |
Specifies the device's intended applications in dental procedures.
Provides crucial safety guidelines for operating the PerioScan unit.
Explains warning symbols and proper disposal procedures for the device.
Details the PerioScan model, voltage, output, and water requirements.
Outlines environmental conditions for operation and storage, including protection classes.
Identifies and describes the main switches, sockets, handpiece, and foot switch.
Lists all components included in the PerioScan package.
Instructions on correctly applying safety and laser warning labels to the unit.
Step-by-step guide for connecting the unit, handpiece, and foot switch.
Details on how to fill the tanks with approved rinsing media.
How to power on the unit and prepare it for operation.
Adjusting rinsing medium supply and power settings.
Details on increasing/decreasing abrasive power in increments.
Using pre-programmed PERIO settings for different applications.
How to customize PERIO key settings for specific needs.
Procedure to restore default unit settings.
Operating the handpiece with foot switch modes.
How to turn off the boost function for continuous operation.
Maximum power levels for various instrument tips.
Procedure to check minimum water flow rate on the hose.
Explains how the detection mode works, including visual and audible feedback.
Describes how to use images for patient communication during treatment.
Details the usage of function keys for mode selection and control.
Explains the signal mode for detection feedback and volume adjustment.
Instructions on how to update the PerioScan's detection software.
How to activate a demonstration mode for showcasing the PerioScan's features.
Procedures for disinfecting and cleaning the external surfaces of the unit.
Guidelines for cleaning the foot switch and protecting against medicaments.
Details on cleaning and thermally disinfecting the media tanks.
Methods for cleaning the handpiece, water channel, and light guides.
Guidelines for external spray and wipe disinfection of the handpiece.
Detailed steps for autoclaving the handpiece and tips according to safety standards.
Instructions on how to clean or replace the filter insert in the water supply hose.
Step-by-step guide for combating biofilm formation in waterlines using MicroCLEAR.
Describes the monthly rinsing procedure to remove mineral deposits from water lines.
Explains the "Service" display and initial troubleshooting steps.
Lists display errors, their descriptions, and corrective actions.
Lists malfunctions without display errors and their corrective actions.
Covers issues with keyboard, foot switch, and connectivity problems.
Guidelines to prevent damage from electrostatic discharge to the unit.
Explanation of how static electricity builds up and its effects.
Details the unit's compliance with standards for electromagnetic emissions.
Specifies the unit's immunity levels to various electromagnetic interference tests.
Recommends minimum distances for portable/mobile HF devices to prevent interference.
Lists general spare parts for the PerioScan unit with order numbers.
Catalog of available instrument tips for the PerioSonic handpiece.
Explains key combinations for signal mode and activating/deactivating detection.
Details key combinations for patient communication, reset, and boost function.
How to use key combinations for learning program and demonstration mode.
To Next Page
