Need help?Do you have a question about the Sirona C3 Plus and is the answer not in the manual?
General| Model | C3 Plus |
|---|---|
| Type | Dental Unit |
| Manufacturer | Sirona |
| Patient Chair | Integrated |
| Operating Light | LED |
| Control Panel | Integrated |
| Foot Control | Optional |
| Cuspidor | Integrated |
| Suction System | High and Low |
| Compressor | Optional |
| Assistant Element | Optional |
| Power Requirements | 220-240V, 50/60Hz |
| Weight | Approx. 300 kg |
Welcome message and overview of the C3+ treatment center.
Provides contact information for customer service and manufacturer.
Explains the meaning of DANGER, WARNING, CAUTION, NOTICE, and IMPORTANT symbols.
Describes symbols indicating how to use the unit and where to find documents.
Lists compliance with various international and national standards (IEC, ISO, CE, CSA).
Provides detailed specifications for the treatment center (power, current, protection).
Illustrates and lists all components of the C3+ treatment center with reference numbers.
Explains the system status display, mode key, and basic settings.
Details the main functions and buttons on the assistant element control panel.
Instructions for initial setup, including sanitation and main switch operation.
How to manage chair and instrument programs for two users (A/B).
Introduction to the wireless foot switch and its registration process.
Explains the 4-way foot switch plate and its operational functions.
Safety precautions for patient positioning and movement range to avoid collisions.
How to stop chair movements and what warning signals are activated.
Instructions for manually adjusting the articulated headrest.
Instructions for adjusting the flat headrest and magnet warning.
Adjusting patient height and mandibular position for optimal access.
How to control chair movements using keys and foot switch.
Information on the dentist element's maximum load capacity.
How to position the dentist element and operate the swivel arm.
Explains spray function, amount adjustment, and chip blower operation.
Setting speed and counterclockwise rotation for the electric motor.
How to start and operate the highspeed handpiece, including air pressure display.
Intensity setting and tip protector usage for the scaler.
Usage, safety, and instrument light for the SPRAYVIT L syringe.
Procedures for preparing and using the NaCl pump for surgery.
How to control the operating light intensity and modes from dentist/assistant panels.
How to fill the tumbler and settings for continuous operation.
How to activate cuspidor flushing and set the timer.
Procedures for purging water paths and using the auto-purge function.
How to access and change basic settings using the Mode key and key lock.
Displays next maintenance due date and prompts.
Preselecting foot switch control mode and setting time/date.
Performing white balance and setting instrument light/torque.
How to swivel the assistant element and adjust swivel movement.
Operation of vacuum system, safety information, and suction flow control.
Functions and safety of SPRAYVIT L, including instrument light.
Safety instructions and warnings for the LED curing light.
How to swivel the cuspidor and adjust water amount.
Amalgam rotor information and optional disinfection system.
Monitor versions, warnings about approved monitors, and installation.
Details SIROCAM 3 and SIROCAM C camera features.
Operation, safety, and functions of the SIROCAM 3 intraoral camera.
Operation, safety, and functions of the SIROCAM C intraoral camera.
Two operating modes (VIDEO, PC) and switching between them.
Operation in video mode, saving images, and picking up camera.
Switching between quad/single image views and clearing camera memory.
Camera back actions and cursor navigation through images.
Operation in PC mode, picking up camera, and saving images in SIDEXIS/VIDEXIS.
Operation in video mode, picking up camera, and generating still images.
Steps to delete all camera memory images.
Operation in PC mode, picking up camera, and saving images.
Procedures for switching to video mode from PC mode.
Procedures for switching to PC mode from video mode.
Using SIVISION 3 as a monitor for PC functions.
Connecting external accessories and DVGW approval.
Hygienic headrest protection and seat cushion details.
Folding armrest and hydrocolloid coolant supply.
X-ray image viewer operation and tray information.
Responsibility of the practice team for cleaning and care.
Annual inspection by service engineer and maintenance prompts.
Importance of periodic safety tests (every 2 years) for electrical faults.
Information on environmentally sound disposal and procedure in Germany.
Note for disposal company regarding batteries and their removal.
To Next Page
