34
Function
MD N X
x
M of CURSOR knob
m of CURSOR knob
CD SYNC HIGH SPEED
PLAY MODE
CD SYNC HIGH SPEED (*1)
MD Z
REPEAT
“CPLAY2MID” t “CPLAY2OUT” t “CPLAY2IN”
“CREC 2MID” t “CREC 2OUT” t “CREC 2IN”
Contents
Sets continuous playback when pressed in the STOP state. When pressed during continuous playback,
the tracking servo turns ON/OFF
Stops continuous playback and continuous recording
The sled moves to the outer circumference only when this is pressed
The sled moves to the inner circumference only when this is pressed
Switches between the pit and groove modes when pressed
Switches the spindle servo mode (CLV S y CLV A)
Switches the displayed contents each time the button is pressed
Ejects the disc
Releases the test mode
Z
Z
*1) Press the [CD SYNC NORM SPEED] button to lights up “IT” indicator, then press the [CD SYNC HIGH SPEED] button.
4-5-1. Operating the Continuous Playback Mode
1. Entering the continuous playback mode
(1) Set the disc in the unit. (Whichever recordable discs or discs for playback only are available)
(2) Turn the
[ENTER/YES] knob to display “CPLAY2MODE” (C36).
(3) Press the [ENTER/YES] button to change the display to “CPLAY2MID”.
(4) When access completes, the display changes to “C = AD = )”.
Note: The numbers “ ” displayed show you error rates and ADER.
2. Changing the parts to be played back
(1) Press the [ENTER/YES] button during continuous playback to change the display as below.
When pressed another time, the parts to be played back can be moved.
(2) When access completes, the display changes to “C = AD = )”.
Note: The numbers “ ” displayed show you error rates and ADER.
3. Ending the continuous playback mode
(1) Press the [MENU/NO] button. The display will change to “CPLAY2MODE” (C36).
(2) Press the [MD ] button and take out the disc.
Note: The playback start addresses for IN, MID, and OUT are as follows.
IN : 40h cluster
MID : 300h cluster
OUT : 700h cluster
4-5-2. Operating the Continuous Recording Mode (Use only when performing self-recording/palyback check)
1. Entering the continuous recording mode
(1) Set a recordable disc in the unit.
(2) Turn the [ENTER/YES] knob to display “CREC 2MODE” (C37).
(3) Press the [ENTER/YES] button to change the display to “CREC 2MID”.
(4) When access completes, the display changes to “CREC 2( ” and “ REC ” lights up.
Note: The numbers “ ” displayed shows you the recording position addresses.
2. Changing the parts to be recorded
(1) When the [ENTER/YES] button is pressed during continuous recording, the display changes as below.
When pressed another time, the parts to be recorded can be changed. “ REC ” goes off.
(2) When access completes, the display changes to “CREC 2(
” and “ REC ” lights up.
Note: The numbers “ ” displayed shows you the recording position addresses.
3. Ending the continuous recording mode
(1) Press the
[MENU/NO] button. The display changes to “CREC 2MODE” (C37) and “ REC
” goes off.
(2) Press the [MD ] button and take out the disc.
Note 1: The recording start addresses for IN, MID, and OUT are as follows.
IN : 40h cluster
MID : 300h cluster
OUT : 700h cluster
Note 2: The [MENU/NO] button can be used to stop recording anytime.
Note 3: Do not perform continuous recording for long periods of time above 5 minutes.
Note 4: During continuous recording, be careful not to apply vibration.
4-6. FUNCTIONS OF OTHER BUTTONS
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
To Next Page
Loading...
