3-4
VPL-VW10HT
Perform the same adjustments as in steps 7 to 12 using
B GAIN/BIAS.
15. Press the MEMORY key to save the data.
16. Enter the OTHER on the Device adjust of the menu.
17. Set the 06 3D GAMMA/THROUGH from 1 to 0.
18. Set the 07 3D GAMMA/SW from 0 to 1.
19. Press the MEMORY key to save the data.
3-3-5-2.RGB W/B Low and Custom Adjustment
1. Enter the W/B ADJUST LOW from the PIC. CTRL
menu.
2. Copy the adjusted value of the HIGH mode in the R/G/
B BIAS.
3. Write the following values in the R/G/B GAIN.
R GAIN: adjusted value of HIGH mode
G GAIN: adjusted value of HIGH mode _30
B GAIN: adjusted value of HIGH mode _30
4. Press the MEMORY key to save the data.
5. Write the following values in the WB ADJUST
CUSTOM 1 to 4.
CUSTOM 1: B/G GAIN _10
CUSTOM 2: B/G GAIN _20
CUSTOM 3: B/G GAIN _40
CUSTOM 4: B/G GAIN _50
6. Press the MEMORY key to save the data.
3-4. VIDEO W/B Adjustment
3-4-1. Component W/B High Adjustment
1. Input the Component Flat Field signal to INPUT-A,
and select the COMPONENT by the INPUT-A of the
SET SETTING.
2. Set the 06 3D GAMMA/THROUGH to 0.
3. Set the 07 3D GAMMA/SW to 1 (3D Gamma: ON).
4. Enter the W/B ADJUST HIGH from the menu.
5. Input the 80 IRE Component Flat Field signal to
INPUT-A.
6. Adjust the chromaticity (x, y) to the values shown
below by the G GAIN and B GAIN of the W/B HIGH.
7. Input the 20 IRE Component Flat Field signal to
INPUT-A.
8. Adjust the chromaticity (x, y) to the values shown
below by the R GAIN and B GAIN of the W/B HIGH.
9. Repeat steps 5 to 8 until the chromaticity meets the
below specifications.
10. Press the MEMORY key to save the data.
Specification:
Chromaticity (x) = 0.284 ± 0.005
Chromaticity (y) = 0.297 ± 0.005
3-4-2. Component W/B Low Adjustment
1. Enter the W/B ADJUST LOW from the menu.
2. Input the 80 IRE Component Flat Field signal to
INPUT-A.
3. Adjust the chromaticity (x, y) to the values shown
below by the G GAIN and B GAIN of the W/B LOW.
4. Input the 20 IRE Component Flat Field signal to
INPUT-A.
5. Adjust the chromaticity (x, y) to the values shown
below by the R GAIN and B GAIN of the W/B LOW.
6. Repeat steps 2 to 5 until the chromaticity meets the
below specifications.
7. Press the MEMORY key to save the data.
Specification:
Chromaticity (x) = 0.313 ± 0.005
Chromaticity (y) = 0.329 ± 0.005
3-4-3. W/B Low Custom Adjustment
1. Copy the data in the CUSTOM 1 to 4 using the
menu.
CUSTOM 1: GAIN = RGB/HIGH
BIAS = VIDEO/HIGH
CUSTOM 2: GAIN = RGB/HIGH + 40
BIAS = VIDEO/HIGH
CUSTOM 3: GAIN = VIDEO/LOW + 40
BIAS = VIDEO/LOW
(R GAIN is + 0)
CUSTOM 4: GAIN = VIDEO/LOW _20
BIAS = VIDEO/LOW
(R GAIN is + 0)
2. Press the MEMORY key to save the data.
To Next Page
Loading...
Need help?
General
