Stid ultrys - Page 135

To Next Page

To Previous Page

     
135 
 
SPECTRE NANO OSDP
TM
 
© STid – MU_ULTRYS_V3.0.1_EN 
 
 
 
 
These parameters must be those used for encoding the Bluetooth
®
 
virtual badge.
 
   
a 
b 
c 
d 
e 
f 
g 
a 
d 
f 
g 
c 

Main Page

Table of Contents3
Information6
Pc Requirements6
Usb Key Content6
Hardware Required6
Windows Installation7
Compatibility ULTRYS / Reader Range / User Ids7
Compatibility Ultrys / Firmware Reader7
Overview8
Open9
Readers Configurable11
Spectre Reader12
Reader Configuration Spectre Read Only13
Ultrys Settings13
Create New Configuration15
Step 1- UHF Frequency Band Regulation16
Step 2- Configuration Protection Loaded into the Reader18
Step 3- Reader Configuration19
Step 4- Antenna Type Selection21
Step 5- Installation Configuration with SPECTRE Antenna22
Step 6- Light Indicator Configuration35
Step 7- Reading & Communication Parameters37
Step 8- User Security Roles42
Step 9- Configuration Save and Protect43
Reader Configuration Spectre Osdp45
Ultrys Settings45
Create New Configuration47
Step 1- UHF Frequency Band Regulation48
Step 2- Configuration Protection Loaded into the Reader50
Step 3- Reader Configuration51
Step 4- Antenna Type Selection53
Step 5- Installation Configuration53
Step 6- Light Indicator Configuration65
Step 7- Reading & Communication Parameters66
Step 8- User Security Roles69
Spectre Nano Reader72
Reader Configuration Spectre Nano Read Only73
Ultrys Settings73
Create New Configuration75
Step 1- UHF Frequency Band Regulation UHF76
Step 2- Configuration Protection Loaded into the Reader78
Step 3- Reader Configuration79
Step 4- Antenna Type Selection80
Step 5- Installation Configuration81
Step 6- Light and Sound Indicator Setting104
Step 7- Reading & Communication Parameters108
Step 8- User Security Roles118
Step 9- Configuration Save and Protect119
Reader Configuration Spectre Nano Osdp122
Ultrys Settings122
Create New Configuration124
Step 1- UHF Frequency Band Regulation125
Step 2- Configuration Protection Loaded into the Reader127
Step 3- Reader Configuration128
Step 4- Antenna Selection129
Step 5- Installation Configuration130
Step 6- Light and Sound Indicator Setting153
Step 7- Reading & Communication Parameters155
Step 8- User Security Roles164
Step 9- Configuration Save and Protect165
Spectre Atx Reader169
Reader Configuration Spectre Atx Read Only170
Ultrys Settings170
Create New Configuration172
Step 1- UHF Frequency Band Regulation173
Step 2- Configuration Protection Loaded into the Reader175
Step 3- Reader Configuration176
Step 4- Antenna Type Selection178
Step 5- Installation Configuration178
Step 6- Light Indicator Configuration185
Step 7- Reading & Communication Parameters186
Step 8- User Security Roles191
Step 9- Configuration Save and Protect192
Reader Configuration Spectre Atx Osdp194
Ultrys Settings194
Create New Configuration196
Step 1- UHF Frequency Band Regulation197
Step 2- Configuration Protection Loaded into the Reader199
Step 3- Reader Configuration200
Step 4- Antenna Type Selection202
Step 5- Installation Configuration202
Step 6- Light Indicator Configuration208
Step 7- Reading & Communication Parameters209
Step 8- User Security Roles212
Step 9- Configuration Save and Protect213
Spectre Atx4 Reader215
Reader Configuration Spectre Atx4 Read Only216
Ultrys Settings216
Create New Configuration218
Step 1- UHF Frequency Band Regulation219
Step 2- Configuration Protection Loaded into the Reader221
Step 3- Reader Configuration222
Step 4- Antenna Type Selection224
Step 5- Installation Configuration224
Step 6- Light Indicator Configuration235
Step 7- Reading & Communication Parameters236
Step 8- User Security Roles241
Step 9- Configuration Save and Protect242
Reader Configuration Spectre Atx4 Osdp244
Ultrys Settings244
Create New Configuration246
Step 1- UHF Frequency Band Regulation247
Step 2- Configuration Protection Loaded into the Reader249
Step 3- Reader Configuration250
Step 4- Antenna Type Selection252
Step 5- Installation Configuration252
Step 6- Light Indicator Configuration263
Step 7- Reading & Communication Parameters264
Step 8- User Security Roles267
Step 9- Configuration Save and Protect268
Open an Existing Configuration270
Configuration File270
Reader Via Usb272
Configuration Badge (Scb/Ocb Uhf)274
Load the Configuration into the Reader276
Loading the Configuration into the Reader277
Configuration Card (Scb/Ocb Uhf)279
User Credentials280
Step 1- Configuration Details Loaded280
Step 2 - User ID Definition283
Step 3- Encoding Tag286
Annex 1: Using the Epc Code Feedback Format and Epc Filter287
Using Mode287
Using Epc Filter and Modes288
Using Secure Mode289
Annex 2: Protocols290
Protocols Clock & Data290
Clock & Data 2B291
Clock & Data 2H292
Protocoles Wiegand293
Wiegand 3I293
WIEGAND 3Ca294
WIEGAND 3Cb294
WIEGAND 3La295
WIEGAND 3Lb295
Wiegand 3Eb296
Wiegand 3W296
Wiegand 3V296
Revision297

Stid ultrys - Page 135

Table of Contents