Need help?Do you have a question about the Stihl FS 510 C-M and is the answer not in the manual?
Explains symbols attached to the machine for identification and operation.
Explains warning symbols used within the manual's text for safety.
Details on approved deflectors for mowing heads and metal cutting attachments.
Instructions for securely mounting the shredder deflector, possibly requiring special tools.
Information on the hardware required for attaching cutting tools to the gearbox.
Details on how to mount various approved mowing heads to the gearbox.
Instructions for fitting grass cutting blades, including deflector checks.
Steps for installing brush knives, including deflector and thrust washer selection.
Procedure for mounting the shredder blade, including deflector and plug usage.
Steps for mounting circular saw blades, including limit stop and plug usage.
Guidance on how to balance the machine for different cutting attachments.
Identifies the key controls for starting and stopping the engine.
Explains the symbols on the choke knob for starting the engine.
Step-by-step instructions for starting the engine correctly.
Initial starting procedures and precautions for a new machine.
Specific starting advice for cold weather conditions.
Advice on starting in very hot weather conditions.
Guidelines for the initial use and break-in of the new machine.
Operating advice during normal use of the machine.
Procedures to follow after completing work with the machine.
Overview of the air filter's function and maintenance.
Step-by-step guide for replacing the air filter element.
Explanation of the electronic engine management system (M-Tronic).
Instructions for operating in cold temperatures, including carburetor preheating.
Guidance on operating in warm temperatures, setting the shutter correctly.
Operating recommendations for moderate temperatures.
Advice for extreme winter conditions and optional equipment.
Steps to remove the spark plug for inspection or replacement.
How to inspect the spark plug for wear and proper function.
Procedure for correctly installing a new or cleaned spark plug.
Steps to remove the starter mechanism from the machine.
Steps to remove the rope rotor assembly.
Instructions for replacing the starter rope.
Steps to install the rope rotor correctly.
How to tension the rewind spring mechanism.
Procedure for installing the complete rewind starter assembly.
Steps to prepare the machine before replacing the nylon line.
Instructions for adjusting the nylon line on the AutoCut mowing head.
Procedure for adjusting the nylon line on the TrimCut mowing head.
Steps for replacing the cutting blades on the PolyCut mowing head.
Checks for proper clamping and movement of the handlebar.
Troubleshooting steps if the handlebar is stiff to adjust.
Steps to fix loose handlebar clamping.
How to adjust the throttle cable for correct engine response.
Overview of maintenance tasks recommended for dealer servicing.
Checks and replacement of the fuel pickup body in the tank.
Inspection of the spark arrestor and spacer in the muffler for proper function.
Checks for the condition and function of antivibration elements.
Identifies the cap for closing the fuel tank.
Identifies the grip for the pull starter.
Identifies the shutter for summer/winter operation.
Identifies the component connecting the spark plug to the ignition lead.
Identifies the muffler and its screen for noise and fire reduction.
Identifies the plate protecting the fuel tank.
Identifies the control for engine speed.
Identifies the switch to turn off the engine.
Identifies the mechanism to prevent accidental throttle activation.
Identifies the part for holding and controlling the unit.
Identifies the connection between shaft and handlebar.
Identifies the screw for locking the handlebar position.
Identifies the part connecting the saw to the harness.
Identifies the protection for the antivibration system.
Identifies the lever for easier engine starting.
Identifies the pump for additional fuel delivery.
Identifies the cover for the air filter.
Identifies the tank for fuel and oil mixture.
Identifies the component to reduce burn and fire risk.
Component for closing the fuel tank.
Grip of the pull starter for engine ignition.
Component with summer/winter positions for carburetor heating.
Connects spark plug to ignition lead.
Reduces noise, diverts gases, and reduces fire risk.
Protects the fuel tank.
Control for engine speed regulation.
Switches off engine ignition.
Prevents accidental throttle activation.
For holding and controlling the unit during operation.
Connects the shaft and bike handle.
Locks handlebar in selected position.
Connects the clearing saw to the harness.
Protects antivibration system housing from wear.
Eases engine starting by enriching mixture.
Provides additional fuel feed for a cold start.
Encloses and protects the air filter.
Holds fuel and oil mixture.
Reduces risk of burns and fire.
Cutting attachment for various mowing tasks.
Reduces injury risk from thrown objects and contact.
Trims nylon line to proper length.
Cutting attachment made of metal for various purposes.
Reduces injury risk from thrown objects and contact.
Metal attachment for shredding and clearing sturdy growth.
Reduces injury risk from thrown objects and contact.
Metal attachment for cutting wood.
Positions brushcutter steady against wood for control.
Information on emission compliance periods and requirements.
Defines emission compliance categories based on operating hours.
Technical details of the engine, including displacement and power.
Specific engine specifications for the FS 510 C model.
Specific engine specifications for the FS 560 C model.
Specifies the weight of the machine without attachments.
Provides the overall length of the machine.
Lists available mowing heads and metal cutting attachments.
Lists optional accessories for various cutting attachments.
To Next Page
General
