Stryker X8000 Service Manual

5
Introduction

is manual is intended to be used as a service guide for
Stryker repair technicians in
the installation, maintenance,
and repair of the Str
yker X8000 Light Source. It is meant
to be used
in conjunction with the X8000 Light Source
User Manual (1000-400-885) and does not replace
existing
documentation.
Service Options
Factory Service
Due to the c
omplexi
ty of the X8000 Light Source, Stryker
recommends that any malfunctioning system be returned
to Stryker Endoscopy for repair or replacement, where
specialized equipment and technicians are available to
perform repairs while maintaining full product quality and
safety. If service is needed either during or a

er the warranty
period:
1.
Contact
Stryker
Endoscopy
at
1-800-624-442
2,
or contact your local Stryker Endoscopy sales
representative.
2.
Package
all
the
component
s
carefully
in
the
original
shipping container, if p
ossible.
3.
Ship the X8000 Light
Source, prepaid and insured, to:
Stryker Endoscopy Customer Service
Att
ention: Repair
Department
5900 Optical Court
San Jose, California 95138
Y
ou may request a loaner unit during the
repair period.
On-Site Service
Stryker Endoscopy accepts responsibility for the e
ff
ects on
safety, reliability, and performance of the equipment only if
readjustments, modi
fi
cations, and repairs have been carried
out exclusively by a person speci
fi
cally authorized by Stryker
Endoscopy to do so.
On-site repair should be carr
ied out only by quali
fi
ed
technicians with the proper test equipment listed in this
manual, so that the safety of operators and patients is not
compromised.
In no event shall
Stryker Endoscopy be liable for incidental
or consequential damages in connection with or arising from
the performance or use of its products a

er unauthorized
modi
fi
cation or repair.
Required Skills,
T
ools, and
Components

e repair procedures described in this manual require a
basic set of
skills, tools, and replacement components.
Skills
Stryker recommends diagnostic and repair procedures be
performed by authorized, quali
fi
ed technicians with training
or experience in
the following:
•
Basic
electronics
techniques
•
Multimet
er
operation
•
Oscilloscope
operation
•
V
ectors
cope
operation
•
BioT
ek
Safety
Analyzer
operation
Tools
Most of the procedures described in this manual can be
performed using a basic tool kit that includes the
items listed
below.
B
a
s
i
c
t
o
o
l
s
A
d
v
a
n
c
e
d
t
o
o
l
s
•
Phillips
screwdriver
•
Flathead
screwdriver
•
8˝
adjustable
wrench
•
Needlenose
pliers
•
Color
video
monitor
•
Glass
fuse
puller
• Multimeter
• Oscilloscope
(20 Mhz or higher)
•
NTSC/
Pal
V
ectors
cope
•
BioTek
Model
601
PRO Safety Analyzer
or equivalent current
leakage tester
Components
Replacement parts are identi
fi
ed in the “Device Diagrams”
section of this manual. Cer
tain components are for in-house
use only and will not be
available to any non-Stryker entity
.
Before any parts are purchased, an
Indemni
fi
cation Letter
must be signed
and submitted to Stryker Endoscopy,
available from Customer Service
at 1-800-624-4422.
Stryker reserves
the right to incorporate improvemen
ts
to the X8000 without notice and will inform customers of
any signi
fi
cant upgrades. All updated parts will be fully
interchangeabl
e with older versions and will
o
ff
er at least the
same level of quality and performance.
For up-to-date informatio
n on upgrades
to the product or
to
this manual, contact your Str
yker representative.
Reference Documents
None of the in-house
Manufacturing Assembly Procedures
(MAPs), Quality Inspection Procedures (QIPs), specialty
tools, jigs, or
fi
xtures listed in this manual are available for
purchase.

Stryker X8000 Specifications

General

Brand	Stryker
Model	X8000
Category	Medical Equipment
Language	English