5-1
5. Heater program｜Heater program list
5. Heater program
This product has heater programs pre-installed as a template. The programs are
optimized according to the protection sleeve types. (▸P.2-10 Selecting heater program)
Category Heater program Details
Recent － The heater program selected recently is listed.
60mm
60mm 0.25
Can be used for heat shrinking 60mm protection sleeves for single
fiber with 0.25mm coating, for example, Sumitomo FPS-1.
60mm 0.25 Quick
Can be used for heat shrinking 60mm protection sleeves for single
fiber with 0.25mm coating, for example, Sumitomo FPS-1. Select
the program if you would like to reduce the heating cycle time. On
the program, the heater is automatically heated up to the pre-
heating temperature when the fusion splicing process is finished.
60mm 0.25 ECO
Can be used for heat shrinking 60mm protection sleeves for single
fiber with 0.25mm coating, for example, Sumitomo FPS-1. ECO
mode is enabled and helps increase heat cycles per battery.
60mm 0.9
Can be used for heat shrinking 60mm protection sleeves for single
fiber with 0.9mm coating, for example, Sumitomo FPS-1.
40mm
40mm 0.25
Can be used for heat shrinking 40mm protection sleeves for single
fiber with 0.25mm coating, for example, Sumitomo FPS-40.
40mm 0.25 Quick
Can be used for heat shrinking 40mm protection sleeves for single
fiber with 0.25mm coating, for example, Sumitomo FPS-40. Select
the program if you would like to reduce the heating cycle time. On
the program, the heater is automatically heated up to the pre-
heating temperature when the fusion splicing process is finished.
40mm 0.9
Can be used for heat shrinking 40mm protection sleeves for single
fiber with 0.9mm coating, for example, Sumitomo FPS-40.
40mm 0.4
Can be used for heat shrinking 40mm protection sleeves of Nano
Sleeves N4 series, for example, Sumitomo FPS-N4-40.
Slim 60mm
S60mm 0.25
Can be used for heat shrinking 60mm semi-shrunk protection sleeves
for single fiber, for example, Sumitomo FPS-61-2.6.
S60mm 0.25
Quick
Can be used for heat shrinking 60mm semi-shrunk protection
sleeves for single fiber, for example, Sumitomo FPS-61-2.6. Select
the program if you would like to reduce the heating cycle time. On
the program, the heater is automatically heated up to the pre-
heating temperature when the fusion splicing process is finished.
S60mm 0.25 ECO
Can be used for heat shrinking 60mm semi-shrunk protection
sleeves for single fiber, for example, Sumitomo FPS-61-2.6. ECO
mode is enabled and helps increase heat cycles per battery.
S60mm0.25+5s
The program which heating duration is 5 sec. longer than “S60mm
0.25”.
S60mm0.25-5s
The program which heating duration is 5 sec. shorter than “S60mm
0.25”.
Slim 40mm
S40mm 0.25
Can be used for heat shrinking 40mm semi-shrunk protection sleeves
for single fiber, for example, Sumitomo FPS-40-2.6.
S40mm 0.25
Quick
Can be used for heat shrinking 40mm semi-shrunk protection
sleeves for single fiber, for example, Sumitomo FPS-40-2.6. Select
the program if you would like to reduce the heating cycle time. On
the program, the heater is automatically heated up to the pre-
heating temperature when the fusion splicing process is finished.
S40mm0.25+5s
The program which heating duration is 5 sec. longer than “S40mm
0.25”.
S40mm0.25-5s
The program which heating duration is 5 sec. shorter than “S40mm
0.25”.
❚
Heater program list
To Next Page
Loading...
