Why is the coolant temperature indicator always at the end of left scale on my SUNWARD SWL2820 Compact Loader?
If the coolant temperature indicator on your SUNWARD Compact Loader is always at the end of the left scale, it could be due to a faulty thermostat or a faulty instrument. You should change both of them.
What to do if starter does not work in SUNWARD SWL2820 Compact Loader?
If the starter in your SUNWARD Compact Loader isn't working when the key is in the START position, there could be a few reasons. There may be faulty cables, so check and repair them. The battery charge might be insufficient, so charge the battery. Also, the main fuse could be faulty, so replace it.
Why does my SUNWARD Compact Loader only move at low speed?
If your SUNWARD Compact Loader only moves at low speed, it could be due to a faulty pump. You should check the pump, then repair or replace it as needed.
What to do if SUNWARD SWL2820 fuel is completely depleted?
If the fuel is completely depleted in your SUNWARD Compact Loader, refuel and bleed the system before starting the engine again.
Why SUNWARD Compact Loader has insufficient traction force?
If the traction force in both travel directions is insufficient for your SUNWARD Compact Loader, consider these potential causes. The endothermic engine might not be reaching maximum speed, so change the diesel oil filter and check the injection pump. The auxiliary fuel pump (gear pump) could be faulty, so repair or replace it. The max pressure valve setting might be incorrect, so reset it. The connection to the servo control could be faulty or the lever angle incorrect, so restore the connection or shift the lever to the correct position. The pressure relief valve setting might be incorrect, so reset it. Excessive oil temperature could also be a factor, so check the oil level and clean the exchanger. Lastly, the travel motor might be faulty, requiring repair or replacement.
Why SUNWARD Compact Loader has insufficient traction force in one direction?
If the traction force is insufficient in only one direction for your SUNWARD Compact Loader, it could be because the endothermic engine is strongly overloaded, so reduce loads due to lifting. It may also be due to an incorrect setting of the max pressure valve relevant to that direction, so set the valve.
Why engine oil pressure warming light doesn't come on in SUNWARD Compact Loader?
If the engine oil pressure warming light does not come on when the engine is stopped in your SUNWARD Compact Loader, it could be due to a faulty bulb or a faulty pressure sensor, in both cases you should change it.
What to do if the starter doesn't work on my SUNWARD SWL2820?
If the starter on your SUNWARD Compact Loader doesn't work when you turn the key to the START position, there are a few potential causes. It could be due to faulty cables, so check and repair them. The battery charge might be insufficient, requiring you to charge the battery. Alternatively, the main fuse could be faulty and needs to be replaced.
How to fix lamps that don't work properly on SUNWARD SWL2820?
If the lamps on your SUNWARD Compact Loader aren't working correctly even when the engine is running at high speed, it could be due to faulty cables or faulty fan belt tension. Check and repair any loose terminals and connections. Also, inspect the belt tension and adjust it, or replace it if necessary.
Why my SUNWARD Compact Loader does not reach maximum speed?
If your SUNWARD Compact Loader isn't reaching its maximum speed, several factors could be at play. The suction filter might be clogged, requiring a change. The endothermic engine itself might not be reaching its maximum speed, suggesting you change the diesel oil filter and check the injection pump. The auxiliary pump (gear pump) could be faulty, necessitating a check, repair, or change. Insufficient pilot pressure needs to be set. Finally, the pressure relief valve setting might be incorrect and should be set to the rated value.
Lists the skid-steer loader models covered by this manual.
Provides details on the manual's scope, including safety, operation, and maintenance.
Operator must have knowledge and experience; training is recommended for new operators.
Explains safety signal words like DANGER, WARNING, CAUTION, NOTICE, and REMARKS.
Explains the meaning of various safety precaution labels and symbols on the machine.
Outlines general safety rules for operation and maintenance, including personal protection.
Details safety precautions to be taken before and during machine operation.
General rules and precautions to ensure safety during maintenance tasks.
Describes the machine's physical layout, including front and rear views.
Details technical data like operating weight, load capacity, dimensions, engine, and electrical systems.
Describes identification plates and serial numbers for machine and engine recognition.
Details safety devices like restrain bars, boom locks, and cabin protection locks.
Explains the function of various gauges and warning lights inside the operator's cabin.
Details the functions and operation of the left and right control joysticks.
Guidelines for operating a new machine during the first 100 hours to ensure proper component break-in.
Essential checks to perform before starting the engine and operating the machine.
Detailed steps for starting the engine under normal and cold weather conditions.
Safety regulations and precautions for moving the machine, including curves and speed.
Operating instructions for the machine's working equipment, such as the boom and bucket.
Instructions for safely parking the machine on level surfaces and slopes.
Instructions and safety precautions for using the quick coupler to attach/detach buckets and other equipment.
Safety regulations and procedures for starting the machine using booster cables.
Recommendations for routine maintenance and service intervals to maintain machine efficiency.
General advice for performing maintenance safely and effectively, emphasizing cleanliness.
A comprehensive plan outlining maintenance tasks at different service intervals (BS, 50, 100, 250, 500, 1000, 2000 hours).
Safety precautions related to the installation and use of optional equipment.
Procedures and safety warnings for replacing optional equipment, including quick coupler use.
Instructions for connecting hydraulic circuits for optional equipment.
Schematic diagram of the machine's electrical system, showing component connections.
A chart listing electrical codes, their names, and functions within the system.
Schematic diagrams illustrating the machine's hydraulic system layout.
General| Brand | SUNWARD |
|---|---|
| Model | SWL2820 |
| Category | Compact Loader |
| Language | English |
To Next Page
