Texecom PREMIER 88 - View ID Data; Configure Radio

Premier 48, 88, 168 & 640 Installation Manual Programming the Control Panel
INS176 97
View iD Data
Yes
+$&+""/1&)0
&"4&1
Menu
9999989898988899
YYYYYYYYYYYYYY
9
A
REA
&


,,-
9
W
89
--"!,+"888
1,")" 1BX
+$&+""/1&)0
Yes
+$&+""/1&)0
&"43"+1,$
0
????
No
Use keys 0 - 9 to enter
the zone number
&


,,-
9
W
89
--"!,+"F888
&,,-9W89
--"!,+"F898
&,,-9W89
--"!,+"898
Press to toggle between
iD Loop and
The status of the zones
will be displayed
0
12
8888999889988999
YYYYYYYYYYYYYY:
Press to toggle
between ormal loop scan
uick loop scan and
Biscuit Mapping
Area
N
Q
Press to edit No
the zone mapping and
wiring options.
&,,-9W89
--"!,+"898H
Press to toggle between
iD Loop and
Use keys to select the
required iD biscuit.
0
12.
Scroll
Press to toggle between
Normally Open and Normally
Closed wiring.
* = Normally Open.
Omit
Omit
Menu
Viewing the iD Data
This option allows the 60IXD expander the iD biscuit data to
be viewed to diagnostic purposes. There are two way of
viewing the data from the expander:
Normal Scan Mode
This is the normal operation mode of the expander and the
data being displayed is the average result of 4 successive
scans of the iD loop.
Quick Scan Mode
In this mode the data being displayed is the result of each
scan of the iD loop. This mode is useful for identifying
problems with biscuits due to interference, high resistance
connections etc.
“iD” is a registered trade mark of Chloride Safety System Limited.
Configure Radio
+$&+""/1&)0
,+#&$2/"!&,
Menu
No
:;
B
:<:A88



B
8@=


,+"
F888
1,")" 1BX
+$&+""/1&)0
Yes
+$&+""/1&)0
&"43"+1,$
:;B888888
B888,+"888
Yes
???
Yes
Press YES to learn
Radio Device
:;
B
:<:A88



B
8@=


,+"
F8><
:;
B
:<:A88



B
8@=


,+"
8><
??
Use keys 0 - 9 to enter the
required device number or
use the SCROLL key to search
e.g. 23 = Device 23
Press NO to map the
device to a zone/user
Use keys 0 - 9 to enter the
required zone/user number or
use the SCROLL key to search
e.g. 64 = Zone 64
Yes
89B888888
B888,+"888
:;BYYYYYY
 1&31""3& "
Activate the Tamper
on the Device
:;
B
:<:A88



B
8@=


,+"
888
Top Line = Serial number
of device
Bottom
and status
Line = Signal strength
and zone/user number
Configuring Radio devices
Up to 32 wireless detectors and up to the maximum number
of users in remote FOBS can be leant on to the system.
Wireless devices can then be mapped on to the system along
with conventional detectors.
The top line on the display shows the serial number of the
device and also the status i.e. Active, Tamper etc.
The bottom line of the display shows the signal strength and
also which zone/user the device is mapped to.

Signal strength should be greater than 30.
The signal range is between 0 and 90
See Radio-Plus installation manual for full details.