EasyManua.ls Logo

THERMACUT EX-TRAFIRE 45SD - Page 3

THERMACUT EX-TRAFIRE 45SD
80 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
EX-TRAFIRE
®
45SD
Operator Manual, Revision T-5 3
Three-phase mains power lead ������������������������������������������������������������������������������������������3-22
Installation of three-phase mains power lead ������������������������������������������������������������������� 3-22
Torch installation step by step ���������������������������������������������������������������������������������������������3-23
Working (ground) cable installation step by step �������������������������������������������������������������3-26
Plasma gas supply ����������������������������������������������������������������������������������������������������������������3-27
Additional gas filtration ��������������������������������������������������������������������������������������������������������3-27
Gas supply installation ���������������������������������������������������������������������������������������������������������3-28
Gas supply regulation ����������������������������������������������������������������������������������������������������������3-28
System CNC interface connection ��������������������������������������������������������������������������������������3-29
Activating an external DC coil with an external power supply ���������������������������������������3-30
Activating an external AC coil with an external power supply ����������������������������������������3-30
Activating an industrial isolated module with an external power supply ����������������������3-31
The circle cutting guide installation - for the FHT-EX
®
105RTXH/105TTH/45TTH ���������3-32
SECTION 4: OPERATION ������������������������������������������������������������������������� 4-35
Front view �������������������������������������������������������������������������������������������������������������������������������4-36
LCD display details ���������������������������������������������������������������������������������������������������������������4-36
Setting of power supply �������������������������������������������������������������������������������������������������������4-37
1� Mode selection� ����������������������������������������������������������������������������������������������������������������4-37
2� Cutting parameters� ����������������������������������������������������������������������������������������������������������4-38
3� Two variants of cutting torch� ������������������������������������������������������������������������������������������4-38
Rear view, Turn ON ���������������������������������������������������������������������������������������������������������������4-39
Rear panel detail �������������������������������������������������������������������������������������������������������������������4-39
Cutting preparation �������������������������������������������������������������������������������������������������������������� 4-40
Manual cutting operation ����������������������������������������������������������������������������������������������������4-40
Hand torch consumables installation ��������������������������������������������������������������������������������� 4-41
Operating the hand torch ���������������������������������������������������������������������������������������������������� 4-42
Operating the torch safety trigger ��������������������������������������������������������������������������������������4-42
Fit the work clamp ����������������������������������������������������������������������������������������������������������������4-43
Edge start cutting ������������������������������������������������������������������������������������������������������������������4-43
Hand torch cutting technique ���������������������������������������������������������������������������������������������4-44
Piercing ����������������������������������������������������������������������������������������������������������������������������������4-45
Gouging ��������������������������������������������������������������������������������������������������������������������������������� 4-46
Alignment of the machine torch FHT-EX
®
45TTM ��������������������������������������������������������������4-46
Machine torch consumables installation ���������������������������������������������������������������������������4-47
Mechanized Cutting Charts,30 A Cutting, Shielded Configuration ����������������������4-48
Mechanized Cutting Charts,30 A Cutting, Shielded Configuration ����������������������4-49
Mechanized Cutting Charts,45 A Cutting, Shielded Configuration ����������������������4-50
Mechanized Cutting Charts,45 A Cutting, Shielded Configuration ����������������������4-51
SECTION 5: MAINTENANCE �������������������������������������������������������������������� 5-52
Routine maintenance �����������������������������������������������������������������������������������������������������������5-53
Consumable parts inspection ���������������������������������������������������������������������������������������������5-54

Table of Contents

Related product manuals