Thermal Dynamics CUTMASTER 102 - Page 2

Thermal Dynamics CUTMASTER 102

120 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Table of Contents

Service Manual1
Table of Contents5
Section 1:General Information9
- Notes, Cautions and Warnings9
- Important Safety Precautions9
- Publications10
- Note, Attention Et Avertissement11
- Precautions de Securite Importantes11
- Documents de Reference13
- Declaration of Conformity14
- Statement of Warranty15
Section 2 System:introduction17
- How to Use this Manual17
- Equipment Identification17
- Receipt of Equipment17
- Power Supply Specifications18
- Input Wiring Specifications19
- Power Supply Features20
Section 2 Torch:introduction21
- 01 Scope of Manual21
- 02 General Description21
- 03 Specifications21
- 04 Options and Accessories22
- 05 Introduction to Plasma22
Section 3 System: Installation25
- Unpacking25
- Lifting Options25
- Primary Input Power Connections26
- Gas Connections28
Section 3 Torch: Installation31
- 01 Torch Connections31
- 02 Setting up Mechanical Torch31
Section 4 System: Operation33
- Front Panel Controls / Features33
- Preparations for Operation34
Section 4 Torch:operation37
- 01 Torch Parts Selection37
- 02 Cut Quality38
- 03 General Cutting Information38
- 04 Hand Torch Operation39
- 05 Gouging43
- 06 Mechanized Torch Operation44
- 07 Parts Selection for Manual and Mechanized Torch Cutting45
Patent Information52
Section 5 System:service55
- General Maintenance55
- Maintenance Schedule56
- Common Faults56
- Fault Indicator57
- Basic Troubleshooting Guide60
- Circuit Fault Isolation62
- Main Input and Internal Power Problems66
- Pilot Arc Problems70
- Main Arc and Controls Problems73
- CNC Interface Problems74
- Test Procedures74
Section 5 Torch:service89
- 01 General Maintenance89
- 02 Inspection and Replacement of Consumable Torch Parts90
Section 6:Parts Lists91
- Introduction91
- Ordering Information91
- Power Supply Replacement91
- Major External Replacement Parts92
- Front Panel Replacement Parts93
- Left Side Replacement Parts94
- Right Side Replacement Parts95
- Replacement Power Supply Parts96
- Options and Accessories96
- Replacement Parts for Hand Torch97
- Replacement Parts - for Machine Torches with Unshielded Leads98
- Torch Consumable Parts (SL100 SV)100
Section 7: Replacement Procedures101
- Scope101
- Anti-Static Handling Procedures101
- Parts Replacement - General Information101
- Major External Parts102
- Front Panel Parts Replacement103
- Left Side Internal Parts Replacement104
- Rear Panel Parts Replacement106
- Right Side Internal Parts Replacement109
Appendix 1: Sequence of Operation(Block Diagram111
Appendix 2: Data Tag Information112
Appendix 3: Torch Pin - out Diagrams113
Appendix 4: Torch Connection Diagrams114
Appendix 5: System Schematic, 208/460V Units116
APPENDIX 6: Publication History118

Related product manuals

Preview: Thermal Dynamics CUTMASTER 151

Thermal Dynamics CUTMASTER 151

Preview: Thermal Dynamics 152 CUTMASTER

Thermal Dynamics 152 CUTMASTER

Preview: Thermal Dynamics CUTMASTER

Thermal Dynamics CUTMASTER

Preview: Thermal Dynamics 42 CUTMASTER

Thermal Dynamics 42 CUTMASTER

Thermal Dynamics CutMaster 38

Preview: Thermal Dynamics CUTMASTER 81

Thermal Dynamics CUTMASTER 81

Preview: Thermal Dynamics CUTMASTER 39

Thermal Dynamics CUTMASTER 39

Thermal Dynamics 51 CUTMASTER

Preview: Thermal Dynamics Cutmaster 82

Thermal Dynamics Cutmaster 82

Preview: Thermal Dynamics CUTMASTER 60i

Thermal Dynamics CUTMASTER 60i

Preview: Thermal Dynamics CUTMASTER A120

Thermal Dynamics CUTMASTER A120

Preview: CE CutMaster 80XL

CE CutMaster 80XL