Getting started
6
EN
Using the remote control for other equipment
This remote control can be used to control other appliances using the programmable buttons VCR, DVD, SAT, AMP and AUX. For
each button you can control the following appliances:
VCR: video recorder
DVD: DVD player
SAT: satellite receiver, cable network
AMP: hi-fi system, Home Cinema amplifier
AUX: any appliance. For instance, if you have two video recorders, you can program the VCR button to control one video recorder, and
program the
AUX button to control the other one.
Note:The TV button is not programmable.
Programming the remote control
Automatic code search
This method can be used to automatically find the most
appropriate code for your appliance.
1. Switch on the appliance you wish to use the remote control
with.
2. Press the relevant button for this appliance on the remote
control, and while holding this button down, press the
standby button until the light or the appliance buttons of the
remote control come on. Release both buttons.
3. Point the remote control at the appliance and press PLAY.
Wait until the light stops flashing. If the appliance has not gone
into standby mode, press the
PLAY button again to continue
the search for the next set of codes. Repeat this operation
until the appliance goes into standby mode.There are around
20 sets of codes.
4. When the appliance goes into standby mode, switch it on again
without using the remote control. Press the
REV button as
many times as is required to return the appliance to standby
mode.
5. Press the STOP button and hold it down until the light or the
appliance buttons of the remote control go off.
Note: you can cancel the programming operation at any time by
pressing the
EXIT button.
Manual programming
This method involves carrying out a manual search for the codes
to be used for controlling your other appliances.
1. Switch on the appliance you wish to use the remote control
with.
2. Press the relevant button for this appliance on the remote
control, and while holding this button down, enter one of the
codes relevant to your make of appliance (there is a list of
codes at the end of this manual). If the light or the appliance
buttons of the remote control flash you have entered the
wrong code or it is not possible to program the remote
control.
3. Point the remote control at the appliance and press the
relevant button (
VCR, DVD, etc). Press the standby
button. If the appliance does not go into standby mode, try
another code.
Depending on the year of manufacture and the type of appliance,
some functions may not be available. Certain codes may cover
more functions than others.Test the functions you can control and,
if appropriate, try other codes. Note here the code(s) which work
best.
When you change the remote control’s batteries, remember
to reprogram it.
VCR
DVD
SAT
AUX
AMP
Video recorder DVD player Satellite receiver Hi-fi system
Press the
VCR
button. Press the
DVD
button. Press the
SAT
button. Press the
AMP
button.
On/Standby On/Standby On/Standby On/Standby
MENU To display the main menu To display the main menu To display the main menu
Vertical scrolling in menus Vertical scrolling in menus Vertical scrolling in menus
Horizontal scrolling in menus Horizontal scrolling in menus Horizontal scrolling in menus
OK To confirm an action To confirm an action To confirm an action
EXIT To close a menu To close a menu To close a menu
0-9 To directly access channels To enter numeric values To directly access channels To select a station using
or enter numeric values or select options in menus or enter numeric values its number
PR+/PR- To change channels To change chapters To change channels To change stations
AV To select AV input To select AV input
REV Rewind Rewind
PLAY Play Play
FWD Fast forward Fast forward
STOP Stop Stop
PAUSE Pause picture Pause picture
REC Record
MUTE To switch the sound off and
back on again
+/- To set the volume level
To Next Page
Loading...
