What causes hydraulic oil leaks in my Toro Multi Pro 5800 Paint Sprayer?
Hydraulic oil leaks can stem from loose or damaged hydraulic fittings or hoses, or missing or damaged O-rings or seals. Tighten or replace any loose or damaged fittings or hoses, and replace any missing or damaged O-rings or seals.
How to resolve a pressure drop when turning on a boom on my Toro Farm Equipment?
To resolve a pressure drop when turning on a boom on your Toro Farm Equipment: * Adjust the boom bypass valve if it's improperly adjusted. * Remove any obstructions in the boom valve body by removing the inlet and outlet connections. * Remove and inspect all nozzles for damaged or clogged nozzle filters.
How to fix a sluggish traction pedal on my Toro Paint Sprayer?
A sluggish traction pedal can occur if the traction control linkage is stuck or binding, the charge pressure is low, the piston (traction) pump servo control valve orifices are plugged or damaged, the piston pump manual servo control assembly is damaged, or the piston pump or wheel motor(s) is worn or damaged. To fix this, address the traction control linkage, increase the charge pressure, clean or replace the valve orifices, and repair or replace the servo control assembly or any worn components.
What to do if my Toro Farm Equipment machine will not operate in either direction?
If your Toro Farm Equipment machine will not operate in either direction, release the parking brake or check the linkage if the parking brake was not released or is not releasing.
What causes a boom section to not spray on my Toro Farm Equipment?
A boom section on your Toro Farm Equipment might not spray due to: * A dirty or disconnected electrical connection on the boom valve. Turn the valve off manually, disconnect the electrical connector, clean all leads, and reconnect it. * A blown fuse. Check the fuses and replace them if necessary. * A pinched hose. Repair or replace the hose. * An improperly adjusted boom by-pass valve. Adjust the boom by-pass valves.
What to do if my Toro Multi Pro 5800 starter does not crank?
If the starter doesn't crank, begin by checking the electrical connections for good contact, as they may be corroded or loose. Also, check if a fuse is blown or loose and correct or replace it. The battery could be discharged, so charge or replace it.
What to do if the pressure drops when I turn on a boom on my Toro Paint Sprayer?
If the pressure drops when you turn on a boom, adjust the boom bypass valve. Also, remove the inlet and outlet connections to the boom valve and remove any obstructions. Remove and inspect all nozzles.
Why is the hydraulic system on my Toro Multi Pro 5800 operating hot?
Several factors can cause the hydraulic system to operate hot. The oil level in the reservoir might be incorrect, the hydraulic hose could be kinked, or the oil may be contaminated or of incorrect viscosity. Other potential causes include engaged or sticking brakes, an open or damaged piston pump by-pass valve, a malfunctioning hydraulic oil cooling system, low charge pressure, incorrect traction circuit pressure, or worn/damaged wheel motor(s) or spray pump motor. A worn or damaged gear pump or piston (traction) pump could also be the reason. To resolve this, verify the oil level, unkink any hoses, replace contaminated oil, inspect the brakes, repair or replace the by-pass valve or cooling system, increase charge pressure, adjust traction pressure and replace any worn motors or pumps.
What to do if a boom valve is leaking on my Toro Multi Pro 5800 Paint Sprayer?
If a boom valve is leaking, stop the spray system and pump, and turn off the sprayer. Disassemble the valve and replace the O-rings, as one may be deteriorated.
What to do if a boom section of my Toro Multi Pro 5800 does not spray?
If a boom section isn't spraying, start by checking the electrical connection on the boom valve; it might be dirty or disconnected. Turn the valve off manually, disconnect the electrical connector, clean all leads, and then reconnect it. Also, check the fuses and replace them as necessary. Look for a pinched hose and repair or replace it. Ensure the boom by-pass valves are properly adjusted.
General| Brand | Toro |
|---|---|
| Model | Multi Pro 5800 |
| Category | Paint Sprayer |
| Language | English |
Guidelines for the safe operation of the turf sprayer, emphasizing awareness and training.
Duties of supervisors in ensuring operator training and establishing safe work procedures.
Requirements for operator and mechanic training, emphasizing comprehension of manuals and safety.
Pre-operation checks and precautions, including reading the manual and operator capabilities.
Procedures for safe handling of chemicals, use of PPE, and hazard awareness.
Operational safety guidelines, including awareness of surroundings and vehicle control.
Information on slowing down, stopping, and factors affecting braking performance.
Guaranteed sound power level of the unit, including uncertainty value.
Sound pressure level at the operator's ear, including uncertainty value.
Measured vibration levels for hands, including uncertainty value.
Measured vibration levels for the whole body, including uncertainty value.
Location and importance of safety decals for operator awareness and safety.
Guidelines for loading the sprayer to maintain stability and avoid loss of control on slopes.
Chart to verify all parts shipped with the machine.
List of included media and additional parts like manuals and training materials.
Procedure to check and adjust boom hinge springs for correct compression.
Steps to remove the shipping bumper from the sprayer.
Description of primary controls for machine movement, braking, and starting.
Description of the display unit showing operating status and diagnostics.
Overview of various controls for pump, agitation, boom lift, and section control.
Information on available optional equipment and accessories.
Emphasis on reading safety instructions and decals to prevent injury.
Daily checks required before operating the sprayer.
Procedures for checking tire pressure before driving.
Procedure to check and maintain the engine coolant level.
Procedure for checking the level of hydraulic fluid.
Pre-operation check of brake pedal travel and condition.
Safety precautions and procedures for adding fuel to the sprayer.
Instructions for safely filling the fuel tank, including capacity and fill level.
How to start and navigate the InfoCenter display for machine information.
Steps to access and navigate the InfoCenter settings menu.
How to change display units for speed, volume, and area.
Procedure to adjust display brightness and contrast for better visibility.
Procedure for cleaning the suction strainer before and after use.
Method to check and tighten tank straps to prevent damage.
Steps for starting the engine, including preheating and warm-up.
Instructions for operating the traction pedal for forward and reverse movement.
How to set and release the ground speed lock for consistent speed.
Procedure for safely shutting down the engine.
Procedure for filling the fresh water tank for safety purposes.
Steps for filling the main spray tank with chemicals and water.
How to move the booms between transport and spray positions.
Using the cradle to secure booms during transport.
Steps for performing the spraying operation, including agitation and section control.
Advice for improving spraying results and efficiency.
Procedure for clearing a clogged nozzle during spraying.
How to select the appropriate nozzle for the task.
Essential steps for cleaning the sprayer system after each use.
Illustration of different positions for the agitation bypass valve knob.
A comprehensive schedule of maintenance tasks based on service intervals.
Safety precautions and procedures for safely lifting the sprayer.
Steps to remove the forward heat shield for engine access.
Procedure to install the engine heat shield after maintenance.
Steps to remove the seat base access panel.
Procedure to install the seat base access panel.
Lubrication points and procedures for the sprayer pump and fittings.
Lubrication procedure for the boom hinge pivots.
Procedure for lubricating the actuator rod bearings.
Procedure to inspect and clean the air cleaner element and body.
Steps for replacing the air filter element.
Guidelines for changing engine oil and oil filter based on service intervals.
Procedure for replacing the engine oil filter.
Steps for draining old oil and filling with new oil.
Procedure to check the PCV valve for proper function.
Inspection of fuel lines and connections for leaks or damage.
Procedures for servicing the fuel filter and related components.
Procedure for replacing the fuel filter.
Steps for draining and cleaning the fuel tank.
Location and procedure for replacing electrical fuses.
Maintenance procedures for the battery, including cleaning and charging.
Checking wheel lug nut torque and tire condition.
Procedure for changing the fluid in the rear planetary gearboxes.
Steps for checking and changing the engine coolant.
Procedure to adjust the sprayer brakes for optimal performance.
Procedure to check and adjust the tension of the alternator belt.
Recommended hydraulic fluid types and specifications.
Procedures for servicing the hydraulic oil and filter.
Daily inspection of hydraulic lines and hoses for leaks and damage.
Inspection of sprayer hoses and connections for wear and damage.
Procedure for changing the pressure filter element.
Inspection of pump diaphragm and check valves.
Procedure to adjust the length of the actuator rods for boom control.
Procedure to clean radiator fins for optimal cooling.
Procedures for cleaning rate control, agitation, and master boom valves.
Common engine and vehicle problems and their solutions.
Common spray system issues and their corrective actions.
A diagram illustrating the fluid flow within the sprayer system.
To Next Page
