What to do if my Toro Paint Sprayer only operates in one direction?
If your machine only operates in one direction, the traction control linkage may be faulty, or the system charge check valve and/or system relief valve could be defective. Repair or replace the traction control linkage, and repair or replace the system charge check valve and/or system relief valve.
Why won't the starter crank on my Toro Farm Equipment?
The starter may not crank on your Toro Farm Equipment due to several reasons: * Corroded or loose electrical connections: Check the electrical connections to ensure they make good contact. * Blown or loose fuse: Correct or replace the fuse. * Discharged battery: Charge or replace the battery.
What to do if a boom section of my Toro Multi Pro 5800 does not spray?
If a boom section isn't spraying, start by checking the electrical connection on the boom valve; it might be dirty or disconnected. Turn the valve off manually, disconnect the electrical connector, clean all leads, and then reconnect it. Also, check the fuses and replace them as necessary. Look for a pinched hose and repair or replace it. Ensure the boom by-pass valves are properly adjusted.
What to do if a boom valve is leaking on my Toro Multi Pro 5800 Paint Sprayer?
If a boom valve is leaking, stop the spray system and pump, and turn off the sprayer. Disassemble the valve and replace the O-rings, as one may be deteriorated.
Why is the hydraulic system on my Toro Multi Pro 5800 operating hot?
Several factors can cause the hydraulic system to operate hot. The oil level in the reservoir might be incorrect, the hydraulic hose could be kinked, or the oil may be contaminated or of incorrect viscosity. Other potential causes include engaged or sticking brakes, an open or damaged piston pump by-pass valve, a malfunctioning hydraulic oil cooling system, low charge pressure, incorrect traction circuit pressure, or worn/damaged wheel motor(s) or spray pump motor. A worn or damaged gear pump or piston (traction) pump could also be the reason. To resolve this, verify the oil level, unkink any hoses, replace contaminated oil, inspect the brakes, repair or replace the by-pass valve or cooling system, increase charge pressure, adjust traction pressure and replace any worn motors or pumps.
What to do if my Toro Multi Pro 5800 Paint Sprayer loses traction power or won't operate in either direction?
If your machine loses traction power, several issues could be the cause. The brakes might be engaged or sticking, the traction control linkage could be damaged or disconnected, the oil level in the reservoir might be low, or the piston pump by-pass valve could be open or damaged. Additionally, the charge pressure or traction circuit pressure might be low, or the rear wheel motor couplers could be damaged. Inspect and correct the brakes, repair or reconnect the linkage, fill the oil reservoir, repair or replace the by-pass valve, increase the charge pressure, adjust the traction pressure, and repair or replace the motor couplers.
Why is the steering inoperative or sluggish on my Toro Multi Pro 5800?
Several factors can cause inoperative or sluggish steering. The engine speed might be too low, the steering cylinder could be binding, or the oil level in the reservoir might be low. The check valve in the steering control valve could be sticking, worn, or damaged, or the relief valve in the gear pump might be faulty. A worn or damaged steering control valve, internal leaks in the steering cylinder, or a worn or damaged rear gear pump section could also be responsible. To resolve this, increase the engine speed, fix the binding steering cylinder, fill the oil reservoir, and repair or replace any faulty valves or pumps. Also, repair any internal leaks.
What to do if my Toro Paint Sprayer travels too far before stopping?
If the machine travels too far before stopping when the traction pedal is released, it could be due to the traction linkage binding or being out of adjustment, or the traction pedal not returning to the neutral position. Low charge pressure, plugged or damaged piston pump servo control valve orifices, or a damaged piston pump manual servo control assembly could also be the reason. Adjust or unbind the traction linkage, ensure the pedal returns to neutral, increase the charge pressure, and clean or replace valve orifices, and repair or replace the servo control assembly.
Why is hydraulic fluid foaming in my Toro Multi Pro 5800 Paint Sprayer?
Foaming hydraulic fluid can be caused by an incorrect oil level in the reservoir, using the wrong kind of oil in the hydraulic system, an air leak in the piston and/or gear pump suction line, or water contamination in the hydraulic system. To resolve this, correct the oil level, use the correct type of oil, locate and repair any air leaks, and remove any water contamination.
How to fix a sluggish traction pedal on my Toro Paint Sprayer?
A sluggish traction pedal can occur if the traction control linkage is stuck or binding, the charge pressure is low, the piston (traction) pump servo control valve orifices are plugged or damaged, the piston pump manual servo control assembly is damaged, or the piston pump or wheel motor(s) is worn or damaged. To fix this, address the traction control linkage, increase the charge pressure, clean or replace the valve orifices, and repair or replace the servo control assembly or any worn components.
General| Brand | Toro |
|---|---|
| Model | Multi Pro 5800 |
| Category | Paint Sprayer |
| Language | English |
Guidelines for the safe operation of the turf sprayer, emphasizing awareness and training.
Duties of supervisors in ensuring operator training and establishing safe work procedures.
Requirements for operator and mechanic training, emphasizing comprehension of manuals and safety.
Pre-operation checks and precautions, including reading the manual and operator capabilities.
Procedures for safe handling of chemicals, use of PPE, and hazard awareness.
Operational safety guidelines, including awareness of surroundings and vehicle control.
Information on slowing down, stopping, and factors affecting braking performance.
Guaranteed sound power level of the unit, including uncertainty value.
Sound pressure level at the operator's ear, including uncertainty value.
Measured vibration levels for hands, including uncertainty value.
Measured vibration levels for the whole body, including uncertainty value.
Location and importance of safety decals for operator awareness and safety.
Guidelines for loading the sprayer to maintain stability and avoid loss of control on slopes.
Chart to verify all parts shipped with the machine.
List of included media and additional parts like manuals and training materials.
Procedure to check and adjust boom hinge springs for correct compression.
Steps to remove the shipping bumper from the sprayer.
Description of primary controls for machine movement, braking, and starting.
Description of the display unit showing operating status and diagnostics.
Overview of various controls for pump, agitation, boom lift, and section control.
Information on available optional equipment and accessories.
Emphasis on reading safety instructions and decals to prevent injury.
Daily checks required before operating the sprayer.
Procedures for checking tire pressure before driving.
Procedure to check and maintain the engine coolant level.
Procedure for checking the level of hydraulic fluid.
Pre-operation check of brake pedal travel and condition.
Safety precautions and procedures for adding fuel to the sprayer.
Instructions for safely filling the fuel tank, including capacity and fill level.
How to start and navigate the InfoCenter display for machine information.
Steps to access and navigate the InfoCenter settings menu.
How to change display units for speed, volume, and area.
Procedure to adjust display brightness and contrast for better visibility.
Procedure for cleaning the suction strainer before and after use.
Method to check and tighten tank straps to prevent damage.
Steps for starting the engine, including preheating and warm-up.
Instructions for operating the traction pedal for forward and reverse movement.
How to set and release the ground speed lock for consistent speed.
Procedure for safely shutting down the engine.
Procedure for filling the fresh water tank for safety purposes.
Steps for filling the main spray tank with chemicals and water.
How to move the booms between transport and spray positions.
Using the cradle to secure booms during transport.
Steps for performing the spraying operation, including agitation and section control.
Advice for improving spraying results and efficiency.
Procedure for clearing a clogged nozzle during spraying.
How to select the appropriate nozzle for the task.
Essential steps for cleaning the sprayer system after each use.
Illustration of different positions for the agitation bypass valve knob.
A comprehensive schedule of maintenance tasks based on service intervals.
Safety precautions and procedures for safely lifting the sprayer.
Steps to remove the forward heat shield for engine access.
Procedure to install the engine heat shield after maintenance.
Steps to remove the seat base access panel.
Procedure to install the seat base access panel.
Lubrication points and procedures for the sprayer pump and fittings.
Lubrication procedure for the boom hinge pivots.
Procedure for lubricating the actuator rod bearings.
Procedure to inspect and clean the air cleaner element and body.
Steps for replacing the air filter element.
Guidelines for changing engine oil and oil filter based on service intervals.
Procedure for replacing the engine oil filter.
Steps for draining old oil and filling with new oil.
Procedure to check the PCV valve for proper function.
Inspection of fuel lines and connections for leaks or damage.
Procedures for servicing the fuel filter and related components.
Procedure for replacing the fuel filter.
Steps for draining and cleaning the fuel tank.
Location and procedure for replacing electrical fuses.
Maintenance procedures for the battery, including cleaning and charging.
Checking wheel lug nut torque and tire condition.
Procedure for changing the fluid in the rear planetary gearboxes.
Steps for checking and changing the engine coolant.
Procedure to adjust the sprayer brakes for optimal performance.
Procedure to check and adjust the tension of the alternator belt.
Recommended hydraulic fluid types and specifications.
Procedures for servicing the hydraulic oil and filter.
Daily inspection of hydraulic lines and hoses for leaks and damage.
Inspection of sprayer hoses and connections for wear and damage.
Procedure for changing the pressure filter element.
Inspection of pump diaphragm and check valves.
Procedure to adjust the length of the actuator rods for boom control.
Procedure to clean radiator fins for optimal cooling.
Procedures for cleaning rate control, agitation, and master boom valves.
Common engine and vehicle problems and their solutions.
Common spray system issues and their corrective actions.
A diagram illustrating the fluid flow within the sprayer system.
To Next Page
