Why won't the mower deck run when the PTO switch is engaged on my Toro Lawn Mower?
If the mower deck does not run when you engage the PTO switch on your Toro Lawn Mower, make sure you are sitting in the operator’s seat and that the hopper is in the fully lowered position.
What to do if the engine-oil warning light illuminates on my Toro Lawn Mower?
If the engine-oil warning light comes on in your Toro Lawn Mower, it indicates insufficient engine-oil pressure. Check the engine-oil level and add oil if necessary. If the problem persists, change the engine oil and the engine-oil filter.
What to do if the dash panel lights turn on but the starter motor doesn't turn on my Toro ProLine H800?
If the dash panel indicator lights turn on when the key switch is in the ON position, but the starter motor doesn't turn on your Toro Lawn Mower, the battery may not be providing enough current, so charge the battery. Ensure the traction pedal is in the NEUTRAL position and that you are sitting in the operator’s seat. Also, make sure the PTO is disengaged.
Why does my Toro Lawn Mower vibrate while operating?
If your Toro Lawn Mower vibrates during operation, it could be due to unbalanced blades. Try balancing the blades, or replace them if they are damaged. Also, check for any loose bolts, such as the blade bolts, engine bolts, and frame screws, and tighten them as needed.
What to do if my Toro ProLine H800 Lawn Mower engine shuts off while the PTO is still engaged?
If your Toro Lawn Mower engine shuts off while the PTO is engaged, the PTO switch may be malfunctioning, so check its function. Ensure you are sitting in the operator's seat. Also, make sure the hopper is closed and lowered. Finally, check that the parking brake is disengaged, especially if the traction pedal is pressed down.
What to do if the cut is uneven with my Toro Lawn Mower?
If you notice an uneven cut and insufficient collection with your Toro Lawn Mower, several factors could be the cause. Make sure the tires are properly inflated and adjust the mower deck to be parallel to the ground. Check if the blades are mounted correctly and sharpen or replace them if necessary. Also, adjust the PTO belt tension. If your travel speed is too fast for the grass height, slow down. Ensure that the chute is not blocked by cleaning it and verify that the maximum engine speed is 3000 rpm. Additionally, clean the grass-catcher screen.
Why won't my Toro Lawn Mower start, even though the starter motor turns?
If the starter motor turns but the engine doesn't start on your Toro Lawn Mower, check the fuel-tank level and refill if needed. Inspect and replace the fuel filter if necessary. Make sure the vent on the fuel-tank cap isn't blocked. Allow the glow-plug warning light to switch off, or shut off the engine and turn the key to the ON/PREHEAT position for a second glow cycle.
What to do if the starter motor turns, but the engine does not start on my Toro Lawn Mower?
If the starter motor turns but the engine doesn't start on your Toro Lawn Mower, check the fuel-tank level to ensure fuel is flowing through the system. Inspect and replace the fuel filter if necessary. Make sure the vent on the fuel-tank cap isn't blocked. If the engine is cold, wait for the glow-plug warning light to switch off, or shut off the engine and turn the key to the ON/PREHEAT position for a second glow cycle.
General| Brand | Toro |
|---|---|
| Model | ProLine H800 |
| Category | Lawn Mower |
| Language | English |
General safety instructions and warnings for operating the machine safely.
Safety checks, daily maintenance, and pre-operation procedures.
Safety precautions, slope operation, and engine starting procedures.
Procedure for safely shutting down the machine's engine.
Safety precautions and procedures following operation.
Safety precautions related to engine maintenance.
Instructions for servicing and cleaning the air cleaner.
Information on engine oil type, viscosity, and capacity.
Step-by-step guide for changing the engine oil and filter.
Safety precautions for working on the electrical system.
Information on fuse locations and types for electrical system protection.
Checking and adjusting the rear wheel alignment.
Safety precautions related to the cooling system.
Procedure for checking the coolant level in the expansion tank.
Procedures for servicing the PTO belts, including tension checks.
Safety precautions when working with the hydraulic system.
Procedure for changing the hydraulic fluid and filter.
Procedures for blade inspection, sharpening, and balancing.
Procedure for sharpening and balancing mower blades.
To Next Page
