Toshiba e-STUDIO355 - Page 12

e-STUDIO205L/255/305/355/455 © 2009 TOSHIBA TEC CORPORATION All rights reserved
CONTENTS
2
3.4.9 Background offsetting adjustment for RADF ................................................... 3-27
3.5 Image Quality Adjustment (Printing Function)................................................................. 3-28
3.5.1 Adjustment of smudged/faint text .................................................................... 3-28
3.5.2 Adjustment of image density............................................................................ 3-29
3.5.3 Gamma balance adjustment............................................................................ 3-30
3.6 Image Quality Adjustment (Scanning Function).............................................................. 3-31
3.6.1 Gamma balance adjustment............................................................................ 3-31
3.6.2 Density adjustment .......................................................................................... 3-32
3.6.3 Judgment threshold for ACS............................................................................ 3-33
3.6.4 Sharpness adjustment ..................................................................................... 3-33
3.6.5 Setting range correction................................................................................... 3-34
3.6.6 Background adjustment ................................................................................... 3-35
3.6.7 Fine adjustment of black density ..................................................................... 3-36
3.6.8 RGB conversion method selection .................................................................. 3-36
3.6.9 Adjustment of saturation .................................................................................. 3-36
3.6.10 Background processing offset adjustment....................................................... 3-37
3.7 Image Quality Adjustment (FAX Function)...................................................................... 3-38
3.7.1 Density adjustment .......................................................................................... 3-38
3.7.2 Adjustment of image density............................................................................ 3-39
3.8 Adjustment of High-Voltage Transformer........................................................................ 3-40
3.8.1 Adjustment....................................................................................................... 3-40
3.8.2 Precautions...................................................................................................... 3-46
3.9 Adjustment of the Scanner Section................................................................................. 3-48
3.9.1 Carriages ......................................................................................................... 3-48
3.9.2 Lens unit .......................................................................................................... 3-52
3.10 Adjustment of the Paper Feeding System....................................................................... 3-55
3.10.1 Sheet sideways deviation caused by paper feeding........................................ 3-55
3.11 Adjustment of Developer Unit ......................................................................................... 3-58
3.11.1 Doctor-to-sleeve gap ....................................................................................... 3-58
3.12 Adjustment of the RADF ................................................................................................. 3-61
3.12.1 Adjustment of RADF position........................................................................... 3-61
3.12.2 Adjustment of RADF height ............................................................................. 3-66
3.12.3 Adjustment of skew.......................................................................................... 3-68
3.12.4 Adjustment of the leading edge position.......................................................... 3-71
3.12.5 Adjustment of horizontal position..................................................................... 3-73
3.12.6 Adjustment of copy ratio .................................................................................. 3-74
3.12.7 Adjustment of RADF opening/closing sensor .................................................. 3-75
3.13 Adjustment of the Finisher (MJ-1025) ............................................................................. 3-76
3.13.1 Adjusting the folding position (Electrical system (Finisher/Saddle unit)) ......... 3-76
3.13.2 Adjusting the sensor output (Electrical system (Puncher unit; option)) ........... 3-77
3.13.3 Registering the number of punch hole
(Electrical system (Puncher unit; option)) ........................................................ 3-78
3.13.4 After replacing the EEPROM (IC1002)
(Electrical system (Puncher unit; option)) ........................................................ 3-79
3.14 Adjustment of the Finisher (MJ-1024) ............................................................................. 3-80
3.14.1 Adjusting the alignment position (Finisher unit) ............................................... 3-80
3.14.2 Adjusting the staple position (Finisher unit) ..................................................... 3-81
3.14.3 Adjusting the folding position (Saddle stitcher unit) ......................................... 3-83
3.14.4 Fine adjustment of binding/folding position (Saddle stitcher unit).................... 3-85
3.14.5 Sensor output adjustment (Puncher unit) ........................................................ 3-86
3.14.6 Registering the number of punch holes (Puncher unit) ................................... 3-87
3.15 Adjustment of the Finisher (MJ-1101) ............................................................................. 3-88
3.15.1 Adjusting the alignment position ...................................................................... 3-88
3.15.2 Adjusting the stapling position ......................................................................... 3-90
3.15.3 B4-size recycled paper mode settings............................................................. 3-92
3.16 Adjustment of Dogleg...................................................................................................... 3-94
4. BACKUP FUNCTION.................................................................................................... 4-1
4.1 Data Cloning ..................................................................................................................... 4-1