E6581528
iv
6.36.7 Setting of a torque command in panel operation mode ········································································· F-72
6.36.8 Torque-related parameters for panel operation······················································································ F-73
6.37 Tracing functions··········································································································································· F-73
6.38 Integral output power···································································································································· F-76
6.39 Communication function ······························································································································· F-77
6.39.1 2-wire RS485/4-wire RS485·················································································································· F-77
6.39.2 Open network option······························································································································ F-83
6.40 My function ··················································································································································· F-83
6.41 Traverse function·········································································································································· F-84
6.42 Instruction manuals for optionally available devices and special functions··················································· F-84
7. Operation with external signal······························································································································ G-1
7.1 External operation········································································································································· G-1
7.2 Applied operation with input and output signals (operation by terminal board)············································· G-2
7.2.1 Functions of input terminals (in case of sink logic) ················································································ G-2
7.2.2 Functions of output terminals (incase of sink logic) ··············································································· G-5
7.2.3 Setup of input terminal operation time ··································································································· G-9
7.2.4 Analog input filter··································································································································· G-9
7.3 Setup of external speed command (analog signal)······················································································· G-10
7.3.1 Setup by analog input signals (RR/S4 terminal) ···················································································· G-11
7.3.2 Setup by analog input signals (VI/II terminal) ························································································ G-12
7.3.3 Setup by analog input signals (RX terminal)·························································································· G-13
8. Monitoring the operation status···························································································································· H-1
8.1 Screen composition in the status monitor mode ··························································································· H-1
8.2 Monitoring the status····································································································································· H-2
8.2.1 Status monitor under normal conditions································································································· H-2
8.2.2 Display of detailed information on a past trip························································································· H-5
8.3 Changing status monitor function·················································································································· H-6
8.4 Display of trip information ····························································································································· H-8
8.4.1 Trip code display···································································································································· H-8
8.4.2 Monitor display at tripping······················································································································ H-10
8.5 Display of alarm, pre-alarm, etc.··················································································································· H-12
9. Measures to satisfy the standards························································································································ I-1
9.1 How to cope with the CE standard················································································································ I-1
9.1.1 EMC directive ········································································································································ I-1
9.1.2 Measures to satisfy the EMC directive··································································································· I-2
9.1.3 Low-voltage directive····························································································································· I-3
9.1.4 Measures to be taken to satisfy the low-voltage directive······································································ I-3
9.2 Measures to be taken to satisfy the UL/CSA standards················································································ I-4
9.2.1 Caution in installing the inverter············································································································· I-4
9.2.2 Caution in wiring and rated current········································································································ I-4
9.2.3 Caution as to peripheral devices ··········································································································· I-4
9.2.4 Caution as to the protection of motors from overload ············································································ I-5
9.3 Compliance with safety standards ················································································································ I-6
10. Selection of peripheral devices ···························································································································· J-1
10.1 Selection of wiring materials and devices····································································································· J-1
10.2 Installation of a magnetic contactor··············································································································· J-5
10.3 Installation of an overload relay ···················································································································· J-5
10.4 Application and functions of options ············································································································· J-6
10.5 Optional internal devices······························································································································· J-9
10.6 Connection of a DC power terminals ············································································································ J-12
11. Table of parameters ············································································································································· K-1
To Next Page
Loading...
