Traub TNX65 - Remove Transport Retainers from the Machine; Working Area Door; Workpiece Handling with Remnant Removal Device

64 pages

Save Page as PDF

To Next Page

To Previous Page

22.10.2021

TNX65/42

Installing the machine

Remove transport retainers from the machine

The transport retainers are located on the:

• control console

• sliding door

• workpiece handling with remnant removal device

• tool carrier and opposed spindle

Transport retainers

• Working area door

• Workpiece handling with remnant removal device

Transport retainers for

working area door

Workpiece handling with

remnant removal device

Main Page

Table of Contents3
Safety7
Symbols7
Documentation Safety Instructions7
Installation and Layout Diagrams Installation and Layout Diagrams9
Foundation Diagram9
Layout Diagram10
Installation Diagram11
General Data General Data13
Dimensions (Without Additional Attachments)13
TNX65/42 / TNX65/42 with Milling Unit13
Machine Weight and Machine Dimensions13
Tnx65/4213
TNX65/42 with Milling Unit14
Bearing Points14
Information on Transporting the Machine by Truck15
Space Required15
Ambient Conditions16
Substrate, Foundations16
Bottom Sump16
Compressed Air Supply16
Equipment to be Provided16
Pumps and Tanks16
Power Supply17
Main Fuse17
External Data Transmission17
Chip Disposal18
Disposal of Spent Fuels and Fluids18
Compliance with Regulations Concerning Groundwater and Wastewater18
Preparing to Transport a Machine Without Milling Unit Preparing to Transport a Machine Without Milling Unit19
Close Open Hose or Pipe Lines19
Corrosion Protection19
Attach Transport Retainers to the Machine20
Attach Transport Retainers to the Control Cabinet21
Preparing to Transport a Machine with Milling Unit Preparing to Transport a Machine with Milling Unit23
Transport Retainers23
Position of the Transport Retainers23
Remove the Tool Chain and Chain Magazine (Only with Optional 120 Positions)25
Remove the Cover on the Milling Unit with Tool Changer26
Separate the Chain of the Chain Magazine (Only with Optional 120 Positions)27
Remove Upper Part of Chain Magazine28
Transporting the Machine Transporting the Machine29
Delivery of the Machine29
Transport by Crane (Min. Load Capacity 12 T)30
Set of Hoisting Gear and Fittings31
TNX 65/42 Centres of Gravity (Machine with Control Cabinet)32
Transport by Fork Lift Truck33
Transport by Truck34
Installing the Machine Installing the Machine35
Installing the Machine by Crane35
Positioning and Installing the Machine with Transport Rollers36
Lifting the Machine with Hydraulic Jacks37
Positioning the Transport Rollers37
Rough Alignment of the Machine37
Set up Control Cabinet on Wheels38
Remove Transport Retainers from the Control Cabinet38
Aligning the Wheels on the Control Cabinet39
Indicator Lamp39
Remove Transport Retainers from the Machine40
Working Area Door40
Workpiece Handling with Remnant Removal Device40
Transport Retainer for Turret (Tool Carrier / Main Spindle and Opposed Spindle / Milling Unit)41
Installation of the Milling Unit Components Installation of the Milling Unit Components45
Installation of the Tool Chain and Chain Magazine (Only with Optional 120 Positions)45
Install Upper Part of Chain Magazine45
Connect the Chain of the Chain Magazine (Only with Optional 120 Positions)47
Install Cover on Milling Unit with Tool Changer49
Fuels Fuels51
Overview of Fuels51
Pneumatic Connection53
Supply of Compressed Air53
Air Consumption53
Electrical Connection55
Notes55
Alignment, Component Installation and Commissioning57
Precise Alignment of the Machine57
Check / Correct Position and Torsion of the Machine57
Check / Correct with Tool Carrier 258
Secure Machine to the Floor59
Transport and Installation of the Chip Conveyor60
Setting the Level Switch of the Chip Conveyor60
Lubricoolant Unit60
Bar Feeding Mechanisms60
Switching on the Machine61

Related product manuals

Traub TNX65 - Remove Transport Retainers from the Machine; Working Area Door; Workpiece Handling with Remnant Removal Device

Table of Contents

Related product manuals