EasyManuals Logo

TRENDnet TEW-831DR User Manual

TRENDnet TEW-831DR
88 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #32 background imageLoading...
Page #32 background image
© Copyright 2020 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-831DR
29
Wireless Client Bridge Mode
Advanced > Setup > Device Mode
Wireless client bridge mode The function of client bridge mode is to extend wireless
connectivity to multiple wired Ethernet client devices. A typical application where this
mode may be used is in your home entertainment/media center where multiple
network enabled media devices require Internet or network connectivity such as an HD
smart TV, game console, set top box, or DVR. The device will first establish connectivity
(similar to a wireless enabled client device such as a laptop or mobile phone) to your
wireless network (typically provided by a wireless router or access point) and bridge the
connectivity to your network over to the wired client devices using the four LAN switch
ports (1-4). After selecting and applying this mode, click on Wireless > Wireless Network
and click Site Survey to scan for the wireless network to connect and enter the wireless
security key (if required) to establish connectivity to your network. After you have
successfully set up the device to connect to your wireless network, you can plug in the
device in the area where you would like to bridge network connectivity to wired client
devices using the four LAN switch ports (1-4). In this mode, the device can only connect
to one band at a time (2.4GHz or 5GHz) and will not provide any of the access control
features typically provided in router mode.
To configure your TEW-831DR in client bridge mode:
1. Log into your router management page (see “Access your router management page
on page 10).
2. Click on Advanced and click Setup, then click on Device Mode.
3. Select Client Bridge and click Apply & Reboot.
4. Click on Wireless and click on Wireless Network, then click on Site Survey to scan for
available wireless networks.

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the TRENDnet TEW-831DR and is the answer not in the manual?

TRENDnet TEW-831DR Specifications

General IconGeneral
Product colorBlack
Cables includedLAN (RJ-45)
Quick installation guideYes
CertificationFCC, IC
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)0 - 90 %
Output current1 A
Output voltage12 V
AC input voltage100 - 240 V
Power source typeAC
AC input frequency50 - 60 Hz
DSL WANNo
Modulation16-QAM, 64-QAM, 256-QAM, BPSK, CCK, DBPSK, DQPSK, OFDM, QPSK
Wi-Fi bandDual-band (2.4 GHz / 5 GHz)
Wi-Fi standards802.11a, 802.11b, 802.11g, Wi-Fi 4 (802.11n), Wi-Fi 5 (802.11ac)
Top Wi-Fi standardWi-Fi 5 (802.11ac)
WLAN data transfer rate (max)1200 Mbit/s
VPN supportFTP/TFTP/SIP/RTSP/IRC/H.323
Networking standardsIEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.1Q, IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3u
Receiver sensitivity802.11a: -75 dBm @ 54Mbps 802.11b: -90 dBm @ 11Mbps 802.11g: -72 dBm @ 54Mbps 802.11n (2.4GHz): -72 dBm @ 300Mbps 802.11n (5GHz): -72 dBm @ 867Mbps 802.11ac: -61 dBm @ 867Mbps
Ethernet LAN data rates10, 100 Mbit/s
Ethernet LAN interface typeFast Ethernet
Antennas quantity4
Antenna gain level (max)5 dBi
Security algorithms64-bit WEP, 128-bit WEP, WPA, WPA2
Number of products included1 pc(s)
Ethernet LAN (RJ-45) ports3
Weight and Dimensions IconWeight and Dimensions
Depth239 mm
Width155 mm
Height30 mm
Weight228 g

Related product manuals